answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2005-01-12 12:16:39

Under the back seat

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How to replace a fuel filter on the 1994 Mazda mx3?

its on the fire wall


Where is the fuel pressure regulator in a 1993 Mazda mx3?

The fuel pressure regulator is located on the fuel rail of the vehicle.


Why does the Mazda mx3 die when turning right and low on fuel?

Your Mazda MX3 might die when turning right and low on fuel because of a damaged or bent float in the fuel tank. It might also die because of clogged fuel injectors or a clogged fuel filter that becomes more obvious when fuel is low.


How does the fuel regulator on a Mazda mx3 work?

By regulating the fuel pressure


Where is the fuel pressure regulator located on 1993 Mazda mx3 v6?

The fuel pressure regulator is located on the fuel rail of the vehicle. It should be on the head closest to the front of the vehicle.


Where is the fuel filter located on a Mazda MX3 with V6 engine?

on top of the transmission on the drivers side, or if you want to go from the top of the engine remove the battery the air cleaner assembly and you can reach it that way as well


Where is the oil filter located on Mazda mx3?

Just jack the car up, and take a peak underneith, should notice it right off.


Where is the fuel pump on a Mazda mx3 1993located?

The fuel pump on Mx3 is located under the back seat, just pull it off its holded by clips, then you will be able to remove the small metal cover to access the fuel pump, you dont need to remove the tank from the car although its easier to work on.


Where is ecu for Mazda mx3?

its located on the floor behind the consol underneath the dash


Where is the horn located on a 95 Mazda MX3?

its located behind the front bumper by the passenger side headlight


Head gasket bolt torque specs for a Mazda mx3?

What are the head bolt torque specs for a mazda mx3 1600


Where is the fuel pump relay for the 1993 Mazda MX3 1.8L K8 v6?

in engine bay fuse board


Why does your 1995 Mazda mx3 fuel burp apon axcel?

Change your spark plugs. Bosch super plus.


Where is the camshaft position sensor on a 92 Mazda mx3?

It is located on the inside of the distributor . Three pin connector .


When was the Mazda MX3 first produced?

The Mazda MX3 was first produced in 1991. It was introduced at the Geneva Motor Show in March of 1991. The MX3 was produced until 1998, when production was halted.


What causes an oil leak underneath the body in a 1992 Mazda mx3?

A leaking gasket, a leaking filter, or a leaking drain plug....


What is the flasher box in the Mazda mx3?

The flasher box in the Mazda MX3 is the plug in that controls the flashers for the turn signals and also the hazard lights. This part is located under the dash on the driver's side, just above the brake pedal area.


Where is Radiator fan relay located 1992 Mazda mx3?

In the fuse box under the hood, driver's side


Will a 1994 Mazda mx3 dash fit in a 1992 Mazda mx3?

yes, you will have to remove all the plastics from the 94 and put them into the 92, as well as the wiring.


Where is the inertia switch on a 1993 Mazda mx3?

A 1993 Mazda MX-3 does not have an inertia switch. If anything is wrong with what would normally be the inertia switch, the fuel pump may be faulty.


Where is the fuel pump on a 94 Mazda mx3 located?

look underneath the rear seat, the access panel is right there, just undo the four screws, lift the plate and then remove the little screws around the top of your fuel pump. It should pull out easily


Where is the turn signal relay located in a 92 Mazda mx3?

under hood near battery. the flasher is near steering column


How do you set timing on a 1995 Mazda MX3?

This is done the same as the 1995 Mazda MX6. The answer is posted.


How do you change the thermostat on a 1993 Mazda mx3?

waste of time


How do change brake pads on Mazda mx3?

well i just changed the brakes on my Mazda mx3 what you do is take the 2 pins out of the calipers which is holding the pads in place and then you are able to remove the pads