answersLogoWhite
American Cars
Fuel Filters
Fuel Pumps
Ford Explorer XLT

Where is the fuel pump assembly on a 2000 olds intrigue located?

678

Top Answer
User Avatar
Wiki User
Answered
2006-07-21 15:47:21
2006-07-21 15:47:21

In the gas tank. Book procedure for replacing: Remove the negative battery cable. Relieve the fuel system fuel pressure. Remove the rear compartment trim panel - Rear in Body Rear End. Remove the nuts retaining the fuel sender access panel. Remove the fuel sender access panel. Disconnect the fuel sender electrical connectors. Clean the fuel pipes and the fuel sender assembly to prevent fuel contamination during the removal. Disconnect the quick-connect fittings at the fuel sender assembly. Remove fuel sender snap ring retaining the fuel sender. Remove the modular fuel sender assembly. Clean and inspect the O-ring sealing surfaces of the fuel sender assembly . Important Always replace the fuel sender O-rings when reinstalling the fuel sender assembly. The modular fuel sender assembly will spring-up when the snap ring is removed. When removing the modular fuel sender assembly from the fuel tank, the reservoir bucket on the fuel sender assembly is full of fuel. The modular fuel sender assembly must be tipped slightly during removal in order to avoid damage to the float. Place any remaining fuel into an approved container once the modular fuel sender assembly is removed from the fuel tank. Always maintain cleanliness when servicing the fuel system components. Care should be taken not to fold over or twist the fuel pump strainer when installing the fuel sender assembly, as this will restrict fuel flow. Also, ensure that the fuel pump strainer does not block full travel of float arm. Ensure that the snap ring retaining the fuel sender assembly is fully seated within the tab slots on the fuel tank. Position the new fuel sender assembly O-ring on the fuel tank. Install the fuel sender assembly into the fuel tank. The Fuel Sender Assembly is spring loaded, it will be necessary to hold the sender in place. Install the snap ring retaining the fuel sender assembly . Connect the fuel sender assembly electrical connectors. Install the quick-connect fittings at the fuel sender assembly. Connect the negative battery cable. Perform the following procedure to check for fuel leaks: Turn the ignition switch to the ON position for 2 seconds. Turn the ignition switch to the OFF for 10 seconds. Turn the ignition switch to the ON position again. Visually inspect the fuel system for fuel leaks. Install the fuel sender access panel. Good Luck!

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The regulator is part of the fuel pump assembly located in the fuel tank.


The fuel filter is located in the gas tank as part of the fuel pump assembly. So change it whenever you have to replace the fuel pump.


Fuel pump assembly is located inside the fuel tank. The access to it is under right rear seat.


Located in the fuel tank- may have to be removed for access


Sending unit is in the gas tank attached to the fuel pump as an assembly.



It's attached to the fuel pump sending unit, inside the fuel tank.


It is in the fuel tank. It is one assembly which includes the fuel level sender unit, fuel filter, fuel pump and the pressure check valve. If you are asking this, your Durango has about 110k miles on it


Hi, If you are referring to the fuel level sensor, it is located in the fuel tank and is mounted on the fuel pump assembly. Draining and dropping the fuel tank is needed to replace this sensor. Good Luck, Greg


where is the fuel pump relay located on a 2000 toyota corolla


The Fuel filter is an unaccessable part of the fuel pump assembly, located in the gas tank. The assembly includes the fuel pump, fuel level sending unit, and the fuel filter. Search this WIKI information on replacing the fuel pump.


It is located inside the fuel tank.


It in under the driver side rear door, about six inches in. Next to the fuel tank.


the fuel pump is located in the fuel pump module assembly inside the fuel tank


were is the fuel pump relay located in 2000 ford expedition?


where is the fuel shutoff located on 2000 gmc Yukon XL



Fuel pump assembly is located inside the fuel tank.


The Fuel Tank Pressure Sensor on a Oldsmobile Bravada 2000 is on the top of the Fuel Pump Assembly.


on a jeep wrangler the fuel filter is part of the fuel pressure regulator assembly which is located on the fuel pump module..... the fuel pump module is located on top of the fuel tank.....


The fuel filter is located in the fuel tank on a 2000 Acura 3.2 TL. The filter is attached to the fuel pump.


The fuel pump on a 2000 Lincoln Continental 4.6 is located inside the fuel tank. It sends fuel from the tank to the fuel injectors.


It is located in the fuel tank itself.



The fuel filter is located in the fuel sender assembly, inside the fuel tank. Vehicles with dual tanks, have no fuel filter in the rear tank fuel sender assembly.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.