nine times out of ten on the back the opener
Push the " learn " button on your opener in the garage, then push the button in the car until the door opens or closes. There may be a procedure for setting the code on the door opener itself like pushing the learn button again, check your documentation.
Your owner's manual gives instructions on how to do this. Follow their instructions to learn the "code" from your garage remote. The problem you will run into is that most modern garage door openers have what known as a "rolling code" that is constantly changing. So, when you program the button in the car, you'll have to perform a "learn" function on the actual garage door opener. (attached to the ceiling in your garage) You'll need somebody to hold the "learn" button on the garage door mechanism itself while you press the button on your TSX after the car has been programmed with your handheld garage remote.
You should be able to find this information in your owner's manual, but if you do not have one, then you can try the following:Homelink: Hold the button on the homelink system until it begins to blink. Then, while holding that button, hold the button on your garage door opener until the homelink button blinks faster. Next you will need to press and release the 'learn' button on the overhead garage door opener. Then, hold the button on the homelink you just programmed until the garage door closes. (Caution: If you press and hold the 'learn' button it will erase all of the codes programmed into the overhead unit.)
AnswerDepends on the garage door opener you have. For the most part hold the button on the visor until it flashes fast, or slow, Just so you see the light change. Then hold the button on you garage door remote next to the visor until the light on the visor changes again. This should do it. Now if you have a rolling code garage door opener then you need to locate the learn button on the garage door opener motor. Press the learn button until it changes and then run to your car and press the visor button until you see the light on the garage motor hold steady. Good luck.Also, try www.homelink.com
they are not the same brand so most likely no but try it the learn button is on the back of the opener
In most cases you must open the garage door opener to access the program button. Very rarely are the buttons easy to access, this is to make the unit more secure.
Just press the red button on your garage lifter, and when the light flashes press and hold the button in your your car until the light flashes again or the garage door moves.
see http://www.homelink.com/home/home.tml for details General Steps 1) Reset your Car Homelink system (hold two outside buttons for 20 secs, light will blink) 2) program a button on your car homelink system by holding the button, while pressing the button for your garage door on your garage door remote within 3 inches of your car homelink system 3) Train the Grarage Door open to recognize your car's homelink system by pressing learn button on your garage door opener, within 30 sec's press the button that you programed in step 2. see http://www.homelink.com/home/home.tml for details General Steps 1) Reset your Car Homelink system (hold two outside buttons for 20 secs, light will blink) 2) program a button on your car homelink system by holding the button, while pressing the button for your garage door on your garage door remote within 3 inches of your car homelink system 3) Train the Grarage Door open to recognize your car's homelink system by pressing learn button on your garage door opener, within 30 sec's press the button that you programed in step 2.
Press and hold the two outside buttons until the light blinks. Then at the same time press the button on your remote with the button that you want to use on the car. Go to the garage door opener and press the learn button on the unit. Press the button on the car remote, then the two should now work together.
REad the owners manual. But I believe you have to put garage opener in learn or program mode then depress and hold button on the Yukon this will allow it to program itself to you door remote
In order to program any accessory devices to use with a garage door motor, it is necessary to connect to the motor. The way to program accessories is to use the learn button on the back of the motor so it can recognize the accessory and let it open and close the garage door. So yes, you do need to be near the opener.
in the car, press and hold your garage button until it begins to blink, while holding your regular garage door opener near to envoy button. While pressing both buttons, the light should flash rapidly and then go out. You should then have succesfully programed it. If not, try it again, some times needs to learn codes for your garage.