0
Where is the number 1 terminal on the distributor cap of a 91 Chevy 350 I removed it without marking it I need to know which post goes to number 1 very frustrating anyone want a truck?
Wiki User
∙ 16y ago
make your own number one cylinder prong. Put your number one cylinder at top dead center on the compression stroke. The prong that your distributor rotor is know pointing at is you new number one on your cap. continuing installing your plug wires in the proper firing order in a counter clockwise direction from your new number 1 spark plug wire.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How much does it cost to replace O ring in a distributor?
The o-ring is only about a dollar or so and the labor consists of removing the dist. cap, marking where the rotor is pointing as well as marking where the ditributor base is set. After marking reference points, remove the 15mm bolt that holds the dist. retainer in. Gently turn the distributor back and forth while pulling up at the same time.Once the dist. is removed the o-ring will either be under the distributor or around the round hole on the intake. Installation is the reverse of removal, just make sure to reference the marks to ensure proper realignment upon installation.
What do you do if you have removed all of the plugs simultaniously without marking from the distributor posts?
you need to get the wiring manuel for your car or it might be in the book that came with your car.the manuel should give you the firing order for the plugs than match the wires to the firing order.
What does the term neo terminal ileum refer to in a colonoscopy results report?
neo terminal ileum refers to the 'new' terminal ileum, i.e the 'new' last part of the small bowel. It would be referred to as neo or new because the original terminal ileum has previously been removed. If you haven't had the last part of your small bowel removed you would just have a terminal ileum. If you have had the last part of your small bowel removed, you will have a neo terminal ileum.
How take distributor out of Chevy truck do you just take cap off and pick stright up after marking rotor?
Pretty much except I would bring number one cylinder up on the compression stroke then line up TDC on the timing marks, remove cap, note position of distributor and rotor, then pull the distributor up and out, (note that rotor rotates a bit as the dist is removed). This way you have a reference point if something moves.
In order to remove the intake manifold on a 1999 Chevrolet Suburban 5.7 do you have to loosen or remove the distributor?
Yes you do. The distributor must be removed.
How do you install a distributor in a 1996 Yukon?
I removed the distributor in my 96 gmc yukon but I forgot to mark it before removing it.What do I need to do to get it back in.
Do you have to removed the distributor off engine to change pick up coil?
Usually, NO.
Why doesn't Logan International Airport have a Terminal D?
Logan Int'l doesn't have a terminal D because of the Terminal A project. When they were working on the terminal they had to reconfigure terminal C to accommodate Continental and Delta Shuttle. They then removed terminal D and Split it between Terminal C and E. When Terminal A project was done they saved the hastle of reconfiguring the Airport and left it as is. -Ryan:)
Does the magnet on the distributor shaft slide off?
The distributor will need to be removed. The magnet is permanently attached to the distributor shaft and the shaft is held in place by a roll-pin thatpasses through the distributor drive gear on the bottom side of the distributor. Magnet on top, gear down in the engine, distributor shaft and housing in the middle.
How do you set distributor timing on a 2001 mercury villager?
Timing is set by the PCM and is not adjustable. The distributor should always be reinstalled in the same position it was removed from.
Where is the ignition condenser located on a 2003 Toyota Highlander?
The ignition condenser is located inside the distributor. In order to repair the issue, the distributor will need removed and replaced.
Is it okay to remove the positive terminal ahead of the negative terminal why?
It is recommended to remove the negative first. It causes less of a voltage spike if the ground is removed first.
