0
Front of the engine, just below the exhaust manifold.
Front of the engine, just below the exhaust manifold.
Wiki User
∙ 11y ago
Wiki User
∙ 11y agoFront of the engine, just below the exhaust manifold.
Add your answer:
Earn +20 pts
2006 Grand Caravan 33L - when in park engine won't rev above about 3000 rpm No warning lights and drives just fine and engine gets up to 4500-5000 rpm Is rpm limit in park by design or a malfunction?
For most newer vehicles this is normal. It puts unnecessary wear on an engine to rev it high in park/neutral.
Where are the oxygen sensors located on a 1999 dodge grand caravan sport 33l v6?
Let me guess you have a service engine soon light on and the computer is saying it's your Oxygen sensors. Oxygen sensers are normally located on the exhaust pipe, within 12 inches of the exhaust manifold, you will probably have to get underneath the van to see them. I think it's just emissions stuff nothing real important
How many oz in .33L?
33 litre of water is 1,164.042 ounces
How do you adjust the idle on a 1999 Plymouth Grand Voyager 33L?
Everything is set by the computer. If its not idleing right it is probably a throttle body sensor or a idle control sensor or a number of other things. You need to have it hooked up to the computer to check the codes.
How many pounds of tomatoes in a 5 gallon bucket?
Forty five
Where is the horn located on a '93 Pontiac Grand Am SE 33L V6?
On the bottom front passanger side, near side of radiotor - I have a 94, but it's probably the same. There are two horns, one on the left, the other on the right. You have to remove the mud guards that are right in front of the wheels and right behind the bumper. They are a pain to get to and work with.
Where can you get instruction for installation of the belt tensioner on a 1999 Dodge Caravan 33L?
from underneath the vehicle after the belt has been remove use a 15mm or 5/8 deep well socket (can't remember), a long extension and a swivel. place the socket on the back of the tensioner you should be able to feel around and locate it. then position the ext. w/ swivel on the socket hit the ratchet to the left/ up and loosen the bolt. use your right hand to hold hte tension and your left to unscrew the nut..
How do you replace the front lower ball joints on a 1995 Intrepid ES 33L V6 automatic?
You can't service the lower ball joints by themselves. You must replace the entire lower control arm.
Why would a 93 Pontiac grand am se 33l v6 engine click while running?
i would check the harmonic balancer the rubber seal on it probably has come off and you need to lift up the engine to get to it check your oil level... if its low then that could be your problem, if its not low then it could be one of a few things. best case senario, its low oil, worst case, rod knock if your oils fine and it keeps getting worse...have a mechanic look at it.
Where is the fusible link located in a 1989 Buick Century 33L Engine?
thir is on the hot wire that is conected to the startter and one that runs off relays behind right head light and one behind fues box in dash
How do you replace the lower ball joint on a 1991 Plymouth Voyager LE 33L and if special tools are needed what are they?
you need to press them in.if you put your ball joints in the freezer overnight they will shrink.Then heat up your a- arm with a torch and use a jack to pop the frozen ball joints in
How do you change the starter on a 97 Dodge GC 33L?
Put car on ramp or jack-up and support with safety stands. Then disconnect the neg. battery cable. Under the car there is a bolt and a wire connected to the starter. Remove and save to reinstall on new starter. There are 2 nuts attaching the starter to the flywheel. 1 you can see right at the bottom. Loosen it up but don't fully remove until the top one is off. Here comes the fun part. I worked for the top down. Remove the air intake, breather. A bunch of 10 mm bolts If you haven't changed your air filter lately now is a good time so have a new air filter handy. Do it after you changed the starter. Now reach in an extension with a swivel socket works great. you might have to take off that connector on top of the transmission, that little gray box to get access to the bolt. It is 180 deg. from the lower bolt. If the lower 1 was at 6 o'clock this 1 is at 12 o'clock. Look at the bolt pattern on the new starter as a guide. Once you loosen that up and remove. Go back under the car and remove that loose bolt. Wiggle out the old starter and be careful, there a a thin metal shim on these starters, you must remove from the old and put on the new one. Work the new starter into place make sure the shim is positioned correctly and rebolt the bottom,don't fully torque it up until the top is in. Then go back and torque the bottom. Then install the push on wire and rebolt the main starter cable to that center copper stud. put back all the parts removed and then the battery cable. Say good luck and start that engine. You should be smiling. If it is your first time I would give a couple of hours for the job, but once you do it. The next time is 45 mins. good luck. Steve9174536337
