0
Worm gear
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Is there anyway it increase the power out put of a motor?
The power output of a motor can be changed by the use of gears. Gears can be used to increase torque by reducing the speed of the output shaft by placing a large gear on the output shaft, coupled to a smaller gear. Conversely, by using a small gear on the output shaft, coupled to a larger gear, the speed can be increased with a reduction in torque.
How can you modify gear trains to reverse the direction of motion of the output shafts?
use a 3 bevelled gear arrangement akin to what is used in a car differential on the drive axle - it is possible to have a connecting shaft rotating the opposite direction to the original motion of the gears
What type of bearings are found in a drill press?
Ball bearings in the motor, the spindle shaft and the gear stacks.
Where are worm gears used?
worm gears are used in machines that need high gear ratiosspoonsWorm gears are found in some kinds of 90 degree gearing junctions, generally with a large change in gearing ratio.For example, many tillers have worm gears between the input shaft and the crosswise tines.Since a motorcycle doesn't need a true differential, it may also have a worm gear connecting the drive shaft to the rear wheel.An adjustable end wrench (Crescent Wrench) also has a worm gear for adjustment, and it is easily visible.There are some devices such as a telescope stand that have precision adjustment with a worm gear, especially if the only adjust through a fraction of a circle.Worm gears are used to reduce speed. They can be found in factories. Google it to buy one.
What are idler gears and why they are used in the gear train?
a gear in Ur gear box witch allows for a means of reverse
Is there anyway it increase the power out put of a motor?
The power output of a motor can be changed by the use of gears. Gears can be used to increase torque by reducing the speed of the output shaft by placing a large gear on the output shaft, coupled to a smaller gear. Conversely, by using a small gear on the output shaft, coupled to a larger gear, the speed can be increased with a reduction in torque.
What is the function of Bull gear in centrifugal compressor?
a bull gear is used as common driver for pinion gears that are installed on the shaft for each rotor.
What is a gear shaft on a bmx bike?
It'd be a fairly strange BMX if it has a gear shaft. Most "real" BMXes are single speed, their driveline consists of cranks, a bottom bracket and the rear hub. No gear shaft there.
How does an engine works and the function of a gearbox?
An engine is a device that converts chemical energy in the fuel to mechanical and heat energy. This mechanical energy is used to drive a crank shaft which is used to power the wheels of an automobile. The crack shaft is connected to a gear-box which changes the speed and torque of the drive shaft. A lower gear (low speed and high torque) is used for acceleration from halt and a higher gear (high speed and low torque) is used for cruising.
What is an overdrive gear?
A gear which causes the transmission output shaft to rotate at a higher speed than the transmission input shaft.
What does The pinon gear on the pinon shaft meshes with the?
The pinion gear meshes with the ring gear.
How does a manual transmission in a car work?
There are two shafts which run through the gearbox, the input shaft and the output shaft, and the two are connect by pairs of gearwheels, one for every 'gear' of the car. They are paired together: Gear 1 will have a small wheel on the input shaft and a large wheel on the output shaft, meaning less speed and more turning force. Gear 5 will have a large wheel on the input shaft and a small wheel on the output shaft, to ensure a high speed. Moving the gear stick to select a gear pulls a 'synchromesh' into place. This locks the input shaft a gear on the input shaft, allowing the movement to be transferred to the output shaft via that particular 'gear'. In the Neutral setting, the synchromeshes are all disengaged. In Reverse gear, there are three wheels involved in the transmission, instead of two.
What is an intermediate shaft?
An intermediate shaft is a part of a car. It connects the end of the steering column to the rack and pinion gear box and is used to eliminate torque sheer.
If you have a worm gear and a sprocket gear and the worm gear rotates slowly on its shaft how will the sprocket gear turn?
Even slower
What is the angle of the input shaft copared to the output shart to the bevel gear assembly?
the answer to what is the angle to the imput shaft compared to the outout shaft for the Bevel Gear Assembly is : the imput is in the output is out tada that simple!!
Can you turn a input shaft by turning an output shaft?
Manual transmission that is in gear-YES
What is a c clip?
It is a snap ring or retaining ring in the shape of a C, used to keep something like a gear or lever from coming off a shaft, it fits into a groove in the shaft.
