By Ohm's law, voltage is directly proportional to current. You question seems to be missing some detail. Are you talking about an AC dircuit where there is capacitive or inductive reactance present? If so, please note that Ohm's law still applies, but things are a bit more complex with AC and inductance because you now need to consider voltage to current phase angle, as well as how you are measuring things. Please clarify your question.
Voltage, indirectly implies potential "Difference" between that point and infinity. Since potential at infinity is assumed to be zero, voltage at a point is taken as the given value. In a conservative Electric field, this P.D. is independent of the path, hence the resistance has no effect on the magnitude of this voltage.
You can have current without resistance. You would just have zero voltage drop across that zero resistance.However, the question is very interesting, because if you really had zero resistance in the entire circuit, it would be impossible to have any voltage at all without generating an infinite current, so the answer in the theoretical case is no, you can have no current, nor voltage, if there is no resistance at any point in the circuit.
An ideal voltage source has no internal resistance, and a constant voltage output. In reality, all voltage sources (battery, generator, etc.) have some internal resistance, and their voltage may degrade or change over time.Ans 2: An ideal voltage source will have zero input impedance and the voltage can rise to infinity to supply the current.Read more: What_does_an_ideal_voltage_controled_voltage_sources_do
The reason why the break down occurs and getting zero insulation resistance when the Megger test is performed under vacuum is because there needs to be a full test voltage performed. Insulation resistance represents the ratio that is between the applied voltage and the leakage.
The amount of phase shift depends on the resistance that is also present in the system. In an ideal situation, the phase shift would be +90 degrees, but that would require a voltage source with zero resistance, conductors with zero resistance, and an ideal capacitor that exhibited only capacitance.
A capacitor will appear to be an open circuit to a DC source, but only after equilibrium is reached. Proof: A capacitor resists a change in voltage. The equation is ... dv/dt = i/c ... which means that the rate of change of voltage in volts per second is equal to current in amperes divided by capacitance in farads. A DC source has constant voltage. If you charge a capacitor to a constant voltage, then, at equilibrium, dv/dt is zero. This means that i must also be zero, since c is not zero. Ohm's law states that resistance is voltage divided by current. The limit of this is that, when current is zero, then resistance must be infinity. Therefore, the capacitor will have infinite resistance and appear to be open circuited.
The current will be zero if there is no voltage.
there is no voltage and resistance
The value can be anything.As long as the resistance is not zero, if the voltage across the resistor is zero the current through the resistor will also be zero.The relevant equations is...Voltage = Resistance x CurrentIn the special case of superconductivity, the resistance is zero and you can have a current even if the voltage is zero.AnswerResistance is affected by the length of a material, its cross-sectional area, and its resistivity (which, in turn, is affected by temperature). The resistance of a resistor, therefore, is not affected by either voltage or current.
because there is no voltage and resistance?
there is no voltage and resistance
It is not a shunt with zero resistance. It is very small, but it is not zero. The large current develops a small voltage across the small resistance. Measuring that small voltage gives you a proportional measurement of the current.
yes
You can have current without resistance. You would just have zero voltage drop across that zero resistance.However, the question is very interesting, because if you really had zero resistance in the entire circuit, it would be impossible to have any voltage at all without generating an infinite current, so the answer in the theoretical case is no, you can have no current, nor voltage, if there is no resistance at any point in the circuit.
Use thevenin model for the output of the power supply. That means there is a voltage source Vs, output resistance Rs and the series load RL which is a short with a resistance value equal to zero ohms. So, voltage across it is zero. The full voltage drops across the resistance Rs according to KVL.
An ideal voltage source has no internal resistance, and a constant voltage output. In reality, all voltage sources (battery, generator, etc.) have some internal resistance, and their voltage may degrade or change over time.Ans 2: An ideal voltage source will have zero input impedance and the voltage can rise to infinity to supply the current.Read more: What_does_an_ideal_voltage_controled_voltage_sources_do
If you measure zero current, then there are two possibilities,and there's no way you can tell which one is true withoutanother measurement.-- The voltage across the circuit may be zero,and the resistance could be anything.-- The resistance of the circuit may be infinite,and the voltage could be anything.
It could be anything from zero to a million volts.