answersLogoWhite

0


Best Answer

because...the ships doors are heavy and require more support at the

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why do cruise ship doors have two hinges near the top and one near the bottom?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What is the definition of scour pipe?

A scour pipe is used to flush out sediment or release water. It usually runs near the bottom of a dam.


What is a mine shaft?

Shaft mining or shaft sinking refers to the method of excavating a vertical or near-vertical tunnel from the top down, where there is initially no access to the bottom.


Why are sewers egg-shaped?

Sewers are egg-shaped because that shape ensures that they are narrower at the bottom. This shape causes water near the bottom to flow faster, reducing the likelihood of solids being deposited. If solids were deposited, the sewer would eventually silt up and become blocked.


How do you level and plumb a sliding glass door?

The question is a little confusing. If the floor is level you just put the bottom of the sliding glass door track on the floor. With the stationary section of glass in place the one side of the door should now be quite plumb and all you have to do is attach that part of the frame to the house. On the other hand, if you are asking about a door that is already installed and are wanting to plumb the slider, there should be two screws near the bottom of the door sides and two screws near the top. In order to turn the bottom screws it may be necessary to relieve pressure from the top screws and slightly lift the bottom of the door. Adjust the door so that it is parallel to either the stationary glass or the side frame, whichever side has the locking mechanism. LEVEL equalls left to right.....so place door in a bed of silicone greater than the amount the existing floor is out and shim the appropriate side up until the top of door from left to right is level PLUMB is vertical....... top to bottom and left to right with in one side of the jamb;;;jamb must be plumb in both direction and on both sides of jamb within a straight lin of itself for it to be SQUARE....


What is the principle of operation of the automatic door?

The automatic door has a special infrared sensor in which a person walks towards the door then the sensor detects that someone in there, it then activates the electromagnets in the entrance system which allows the door to open at at certain speed.

Related questions

What is the distance between Barcelona cruise port and Barcelona city centre?

About 10 mins walk, the cruise port is very near the bottom of Las Ramblas, it is very central.


Why door handles are not put near hinges?

[object Object]


What is the recommended distance between 3 hinges on door?

The top hinge screws want to pull out of the door and frame due to the cantilevered centre of gravity of the door. At the bottom hinge the opposite happens and the screws are not in tension because the lower part of the door tends to "push" towards the frame. It is therefore common practice to fit two upper hinges close to one another near the top of the door and have the bottom hinge by itself near the bottom of the door. (All the above assuming the door is rigid and have some weight that cannot be negligible). A third hinge fitted midpoint between a top and a bottom hinges serves no purpose other than evenly supporting a thin flexible door against wind etc.


How do you fix sliding glass doors which do not slide?

1- Clean Tracks 2- Grease Tracks 3-Replace Rollers and Tracks There are also adjusting screws located on the doors to lower and higher the rollers. They are located on the edge of the door near the bottom and near the top. You can try that also.


Where is the VIN number located on a 1963 impala?

Near the hinges in the driver's side door jamb.


How do you lower the spare tire on a dodge sprinter?

Open the rear doors, you will see two bolt heads on the bottom near the scuff plate. You turn them counterclockwise with the tire tool to lower the tire.


Do Princess cruise lines have Disney packages?

To get a cruise to Disney world you will need to take a cruise on Disney cruise lines. I don't believe they allow and other cruise lines to dock at the park. However you could go to Florida and see the park then take a cruise from a near by port.


What is the on off switch near left of steering wheel?

cruise control


Is the pier for the cruise ships near the FT Lauderdale airport?

About four miles.


What is the address of Honolulu Cruise Port?

Somewhere in or near Honolulu. That's the best answer I have.


How do you open the hood of an Ford Fiesta?

There is a release under the dash, and if my memory is correct a second release on near the windshield. The hood opens toward the front of the car, the hinges are near the headlights.


Why my cruise control dont work on my 1998 cadillac deville?

90 Percent of cruise control problems caused by defective cruise control release switch located near top of break pedal.