0
Why do you press harder on a remote control when you know the batteries are flat?
Wiki User
∙ 13y ago
so it could work
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why do you press harder on the remote control when you know the batteries are running out?
coz the battery is low
Why do you press harder on a remote control when you know the batteries are getting weak?
Because you are a neanderthal.
How do you connect a remote to the wii?
you open the thingy on the Wii system (a red button) and press that, then you open the thing on the Wii remote (where the batteries go in),which is a red button,and press them both at the same time. if you are talking about a normal remote,then that will not work on the Wii. you should ask an adult or if you are one,then you should know how to do it, but use your brain,not smart dumbo!
When you press the sync button on the wii an on the Wii remote it still doesn't connect?
because you need to have batteries in the remote and the wii has to be plugged in and on
How do you use PIP on a Charter remote control?
To use PIP on a Charter remote control a person will need to press the PIP button on the remote. Then enter the channel number of the station they wish view in the PIP window and press the select button.
How does one reboot their remote for TV?
One can usually reboot a remote one of two ways. Either press and hold the reset switch, if one is present. If not, then take out and replace the batteries in the remote.
How do you program keyless for a Cadillac dts?
Change batteries and press lock and unlock remote at the same time for (8) second.
How do you turn off a Wii remote?
2 ways: Disconnect the batteries from the wii remote, Press the HOME button and go to wii remote and then you can click a button that goes to the reconnect screen this automatically turns the wii remote off.
What buttons on dish remote control DVD?
Once the DISH remote is programmed to your DVD player, it can be operated in AUX mode. To get to that mode, press the AUX button on the upper right corner of the remote control.
How do you reprogram an Astrostart aka astroflex model 1105 remote?
THE REMOTE CONTROL Your remote control has been designed to fit the natural contours of your hands so that it is easier to use. It works off three long-life lithium batteries. It can control two vehicles separately. Up to four remote controls can be assigned to your vehicle. See your dealer for replacement batteries or additional remote controls. NOTE: The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. USING YOUR REMOTE CONTROL Your remote control can transmit on two different channels, allowing control of two separate vehicles. Only the "Panic" command is transmitted on both channels simultaneously (6-button remote only). Audible (piezo) and visual (LED) confirmations are emitted with the 6-button remote while the 5-button remote allows only visual confirmations. CHANNEL 1: CHANNEL 2: To transmit a command on channel 1, press desired button for two seconds. To transmit a command on channel 2, press desired button, then as soon as a tone is heard or that the LED flashes once, release the button for a moment then press it again and hold down for two seconds. A command will not be executed if you do not press button long enough. Only one command is transmitted even when a button is pressed for more than two seconds, except for the "Panic" button, which repeats command as long as button is pressed. The remotes shown may differ from the one(s) included in the kits. BATTERY REPLACEMENT Your remote works off three 3-volt lithium CR-2016 batteries or equivalent. We strongly recommend that you keep a replacement set in your glove compartment. To replace the batteries, remove screw on back of remote case, remove old batteries and replace with new ones. Make sure that batteries point the right way; see illustration opposite. A pictogram in the bottom of the case shows correct battery orientation. CODE LEARNING OF ADDITIONAL TRANSMITTER(S) Four different remote controls can be programmed for a given vehicle. If a fifth remote is added, the first remote is deleted. Note: When the first code learning command is sent, all the old codes are cleared out. therefore if you want to add a new remote, all the old ones must be reprogrammed as well. One or more remote transmitters can be added. To do this, the programming is accessed as follows: 􏰀 Open hood 􏰀 Place key in the ignition and turn to the RUN position 􏰀 Apply the brakes once 􏰀 You now have 10 seconds to turn the key from the RUN to the OFF position 3 times. 􏰀 If this sequence is correctly carried out, the control module flashes parking lights (4 flashes). You may then proceed to the next step. 􏰀 Press the button on the new remote control. When access code of new remote control is memorized, the control module will confirm with flashing parking lights (1 flash). 􏰀 Repeat the above procedures for each remote control that has to be programmed (up to 4 remotes). 􏰀 Apply the brakes. New remote(s) is (are) now added to the system.
Buttons on Wii Remote work but pointer doesn't?
Pull up the flap on the console and press sync (the red button). If that doesn't work, take the back off the remote where the batteries are and press the sync button there at the same time as the console button.
How do you program an LG TV remote with DirecTV?
Select menu, click on system setup, select 'remote', select 'program remote', select 'tv', select your type of TV. Slide the top slider on your remote to 'TV', press and hold the yellow select button and the mute button until the light above TV on the remote flashes twice, enter the first remote code on the screen and then press power to see if the tv shuts off. If the TV does not shut off repeat for the other codes on the screen.
