check brake light switch on brake pedal maybe getting bad
is that even a full question?
The brake lights are a separate circuit from the other lights. Check the fuses and bulbs. If fuses and bulbs are okay I would suspect the brake light switch is at fault.
Yes any tail lights/head lights, pretty much everything but doors will fit on both ford explorer sports and 4dr explorers between the years 1998 and 2001
I'm not a mechanic / technician but the power brake booster is between the brake fluid reservoir and the firewall on your 2001 Ford Explorer ( located in the engine compartment on the drivers side )
The 2001 Ford Explorer rear parking brake is separate from the rear disc brake that stop the vehicle. The rear rotors have a small drum in the inboard side.
If the brake lights stay on that probably means the switch on the brake pedal that activates them is defective.
why does the dome lights stay on when the switch is turened off 2001 ford explorer super
The brake light switch has failed
Bad bulb? They are double filamented with the smaller being for stop lights Corroded socket? Bad ground?
The most common cause for brake lights to be out on a 2001 Mustang GT is a blown bulb. There are some instances where there is faulty wiring.
check your rear light bulbs. it is a two filament light and one is burned out.
check fuses, check brake light switch behind brake pedal.
It is not necessarily the fuse. It could be the switch on the brake that is not closing the circuit.
dodge 2001 Dakota brake lights won't burn Check the fuses. If the fuses are okay check the brake light switch.
Check the brake light switch. This can cause the brake lights to go out. There have been a couple of recalls on the 2001 for this exact problem. Contact your local VW dealer and have the switch replaced.
Sounds like the arm and switch in the steering column.
This is usually cause by a stuck brake light switch on the brake pedal. Replace it.
it maybe the brake switch
More than likely you are having Electrical issues with your 2001 Ford Ranger brake lights. Contact your local service dealer for further information.
If parking lights stay on after the car is turned off on a 2001 Hyundai Elantra than the brake switch is malfunctioning. The brake switch turns off when pressed in and if it does not work the lights of the vehicle will stay on.
There are five steps on how to adjust the parking brake in a 2001 Ford Explorer. Some of the step-by-step instructions are park the vehicle on a flat surface, place the wheel blocks under both front tires, and disengage the parking brake.
There is a switch under brake pedal. This switch controls the brake lights. They some times go bad. Have someone stand behind vehicle while you push on brake pedal, if no brake lights come on. Try pushing the brake switch by hand. Check for power with a voltmeter.
Look behind a panel in the trunk
The 2001 Chevy Blazer brake lights may not work and the third bake stays on because the current light needs to be replaced. A replacement brake light can be purchased at an Auto Parts store like Pep Boys.
Stuck brake light switch, or a short to power somewhere in the brake light circuit.
Check the operation of the brake light switch located usuallyat the upper section of the brake pedal under dash area
for the tail lights all the other lights are working blanking lights brake lights and reverse lights but no tail lights on both side
If the brake fluid level in the brake master cylinder is low ( in your engine compartment ) that will also turn on your emergency brake light just as if the emergency brake was applied
i replaced a brake light bulb in my 2001 golf now none ofthe brake lights are working ! i can not tell which fuse is the one for the brake lights ! please help ?
you need to get a bigger fuse
It requires a scan tool.
its a 2001 ford focus 1.6 petrol
Check the STOP fuse in the passenger compartment Check the switch on the pedestal of the brake pedal.
Check your brake fluid level in the brake master cylinder in your engine compartment when it is low your brake warning light will come on
what color is the negative parking wire and where is located
Check your brake lights,if they are not working it could be your brake light switch or a fuse.If you have no current to your brake lights you will have no current to your shifter release solenoid.If that's not it,could be release solenoid itself.
check the fuse then the bulbs then the brake switch
Remove the tail light housing and replace the bulbs.
The owners manual shows Motorcraft High Performance DOT 3 brake fluid
Sounds like your brake switch is bad, it should be under the dash where the brake pedal comes down. It has a pin coming out the touches the brake lever.
Check the fuse, bulbs or there is a push button switch above the brake pedal that may need align or replace
Probably a bad or mis-adjusted brake light switch
The push button for the fog lights is in the center stack of the dash , to the right of the radio , near the bottom of the radio
abs codes are retreved by juming obd2 terminal 4-12 after codes plump brake petal 6 times
Check out this website..this is how i fixed mine http://www.2carpros.com/forum/2001-jeep-grand-cherokee-laredo---brake-lights-not-working-vt4814.html
check the fuse and all the light bulbs
Number 13 uses 10 AMP fuse
Disconnect the four plastic screws holding the plastic plate in the back of the trunk. This exposes the tail and brake lights.
If the ABS light is on that means a problem has been detected with the Anti-lock Brake System It could be a fuse , a sensor , or some other problem As long as the red " BRAKE " light in your dash is not on , you still have " normal " brakes
Check bulbs Check switch