0
Why does one of the belt wheels on a 94 Buick Century not turn and what can be done about it?
Wiki User
∙ 16y ago
The wheel or pulley that is not turning is locked up and will have to be replaced. If it is a component such as the air conditioner compressor, or water pump, alternator , etc. then that component will have to be replaced. do not operate the engine while this component is locked up or you will destroy the engine
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Buick century license plate bulb replacement?
A Buick Century License Plate Bulb replacement can be done at home. You can go to any auto store to purchase the replacement part. Replacement can also be done at dealerships if needed.
How do you replace the serpentine belt on a 1995 buick century?
must find the belt tension rotator and then either lossen it or use a crow bar to move tension arm . install the serpintine belt and at the same time the tension arm must move to alow the belt to set right on all pullies. it should be obvious as to how the belt goes and the arm,,,once motivated to move up ...to tighten the belt once the install of the belt is done.
How much will it cost to replace serpentine belt on 95 Buick lesabre?
It can cost between $14 and $30 to replace a serpentine belt on a car. The price can raise to $40 or $60 if a person has it done at a car shop.
How do you change front speakers on a 93 Buick century?
The plastic piece that cover the speakers and vent just oulls off and sets back in there when you are done
How do you stop water leaking into a buick century through the cabin air filter?
If water is leaking from the cabin air filter on a Buick Century then the seal must be replaced. Replacing the seal requires removing the glove box to reach the cabin filter. Once done, the seal can safely be replaced.
Will a 1994 Buick Century 3.1 engine replace a 1993 Buick Century 3.3 engine?
Simple answer is no. They use a completely different engine harness. It can be done, but you have to change all the wiring under the hood. The 3300 engine is probly the better engine, but the 3100 engine is a good motor, but are prone to more problems.
Is a 1994 Buick century 3.1 engine compatible to bolt up to a 1993 Buick 3.3 century?
Simple answer is no. They use a completely different engine harness. It can be done, but you have to change all the wiring under the hood. The 3300 engine is probly the better engine, but the 3100 engine is a good motor, but are prone to more problems.
Will 20 inch rims fit on a 1991 buick century you hear the strut tower will get in the way will the 20's fit or will you need to have som work done if so what kind OF work?
Yea dude you should be able to fit them on no problem because i have a 1999 century with 20's on it. If you go onto a website (like discounttire.com) you can type in your vechile type and they will show you what type of wheels can fit your car so you can be 100% sure.
Expect to change the drive belt soon on a 2002 GMC Yukon what other belts or parts should i also change out in this process?
i am assuming, by drive belt,that you mean serpentine belt on engine.if this i correct, you need to also check the belt tensioner for bearing wear. this can only be done when belt is removed.check all other pulley wheels to make sure belt is running straight on them apart from that , there is not much else that can go wrong with em
Can you get your wheels back if car was repoed?
No As far as finance company is concerned the car came with wheels, it has wheels on it when repoed. Done deal.
How do you adjust a serpentine belt on a 1999 Dodge Dakota?
Done automatically by belt tensioner
How do you change the serpentine belt on a 1994 buick regal 3800?
Use an 18mm wrench and place it on the belt tensioner pulley bolt. - The bolt has reverse threading so it will tighten as you apply counterclockwise force. Pull the wrench back towards the passenger compartment with your left hand (It takes some strength but it can be done). Then pulll off the belt from above the alternator. Careful not to let go for it'll ruin your day. Follow the schematic located on the front left of the car as you replace the everwinding belt. Once everything is aligned pull back on the tensioner once more as you finally engage the belt on the alternator. You're done.
