0
Why does the AC clutch engage when the blower switch is turn on and AC button is off 2003 RAM 1500 pick up?
Wiki User
∙ 14y ago
You most likely have a bad a/c - heater controller........
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
If the AC compressor clutch does not kick in and the relay and fuse are ok what could be the problem?
The clutch receives it's signal to engage from a pressure switch in the system. If there is insufficient refrigerant in the system the pressure switch will not close resulting in no power at the compressor clutch to make it engage.
How do you engage the mower for a John Deere stx38?
The STX-38 should have an electric clutch for the mower deck. The switch to engage it is on the right rear fender. It is a toggle switch. You will have to pull up on the switch and forward to engage the blades.
Why doesn't air conditioner clutch engage?
See if hot wire hot with switch on.
Izuzu Rodeo Starter Problem.No solenoid click.Battery ok.Starter relay swapped.Starter will spin when jumped to battery but does not engage without solenoid action.Might be ignition or neutral switch?
It is a neutral switch.Starters on newer Isuzu will have a safety-switch installed, even for manual transmissions. The switch, inside the transmission or clutch, will disable the starter circuit until the vehicle is in the proper "mode" to engage the starter.For automatics, this means the starter won't engage unless the transmission is in Park or Neutral.For manuals, (stick-shifts) this means you must engage the clutch while turning the key. Until you engage the clutch, it will seem like the starter is dead.You can have a look at the related link for some trouble shooting pointers.The safety-switch(called a Mode switch for AT) is on the side of the transmission and the clutch switch is on a bracket in front of the clutch pedal. It is activated (switches on) once the clutch pedal is depressed.
Ac switch 2002 Pontiac has three prongs which two do you jump to get clutch engage?
Dont jump them, its not a switch, its a transducer and you could wreck your pcm by jumping the wrong one. Run a power wire directly to your compressor to get the clutch to engage. If it doent engage then, it is your clutch. Remember to first check refridgerant level and fuses/relays. Good luck.
What does pressure cycling switch do?
The ac pressure cycling switch is designed to engage or dissengage the clutch to keep the proper pressure in the system.
Why blades wont engage 0n your cub cadet 2135 lawnmower?
The clutch is wired with a hot from the battery at all times and requires a ground from the switch to engage. Check for a bad ground wire to the clutch or a bad ground connection.
Where is the neutral safety switch Subaru manual transmission?
The neutral safety switch or (clutch safety switch) is above the clutch pedal near the fire wall. It is a small black (on my Subaru Impreza) button that is about half way between the pedal and where the clutch arm is attached.
How can you bypass the starter lockout switch on a 1990 Toyota Camry standard transmission that should activate and allow the car to start when the clutch is fully depressed?
This answer is based on experience with my aunt's ~1995 Toyota pickup, but it should apply to the Camry, too. I imagine her problem was similar to yours. I had set out to bypass the switch, but ultimately did not have to (read on). Look for the switch behind the clutch pedal. When the clutch is depressed, the switch is engaged when the arm of the clutch pedal presses a button on the switch assembely. Although I am sure that you could bypass the switch, you probably don't need to. On the truck I was working on, the problem was that the button was not fully depressed when the clutch was depressed. You can test whether the switch is working by pushing the button and starting the car. If it works, you can make sure that the switch button gets fully pressed in when the clutch is depressed. The switch is mounted on a piece of sheet metal; using an adjustable wrench or pliers, bend the switch assembly toward the rear of the car. Alternatively, you could shim the button by glueing a piece of plastic to the end of the button. if none of that works, unplug that switch and put a jumper between the 2 wires that go to it.
91 escort pony the clutch and ignition suddenly are not working Any ideas Thanks?
There is a switch on the clutch that won't let the car start unless the clutch pedal is fully depressed. You can turn the key but the starter won't engage. Something stuck under the clutch pedal (matt, etc...) will do it or if someone kicked the switch or possibly the switch has died. You could use a jumper wire to bypass the switch if you had to or just replace the switch.
How is the compressor clutch engaged on the air con system?
When not engaged, the wheel spins freely. When the low pressure switch closes, it closes the electrical circuit to the compressor clutch. This actuates an electromagnet, which pulls the clutch in to engage it.
How do you engage the cutting blade on a john deere 165 hydro riding mower?
There's a yellow switch in the upper right hand portion of the dash. It's the PTO drive. Engage your clutch, pull up on the switch and move it forward, and that should start the blades spinning. If it fails to engage, it could be a bad switch or a bad battery.
