The wires are fine, they were engineered to handle the electrical load of normal operation. If the wires have overheated it's because something shorted out or someone connected the electrical wrong.
How do I replace ignition wires on my 98 Mazda 626 2.0L
unplug wires to coil.remove the 7mm bolt pull coil off.
The ignition coil on a 1998 Honda Civic LX is located under the distributor cap. The distributor is on the passenger side of the motor and has wires running from it to each spark plug. it is usually plastic.
CHECK THE IGNITION SWITCH,,, THEY HAVE A HABIT OF GOING BAD
It is in the very back of the engine. Just follow the spark plug wires from the spark plugs and they will go to the top of the Distributor. That will be the distributor cap that the wires are in.
on top back of engine,to be exact there are 3 coils! the coils have the plug wires on them.
All the engines used in a 1998 Ford Explorer have electronic ignition ( EDIS , Electronic Distributorless Ignition System ) The 4.0 liter EFI , V6 and the 4.0 liter SOHC , V6 use one coil pack for the six sparkplug wires The 5.0 liter , V8 engine uses two coil packs for the eight spark plug wires
HOW DO I REPLACE 1998 camry ignition switch?
It's the box between the engine and left side of the engine compartment where the spark plug wires attach to
I need to replace the ignition switch on a 1998 KIA Sportage . Can this be done with a universal ignition switch ? There are 6 sets of wires going into the KIA switch. The universal switches come with 3 or 4 posts.
To replace the ignition wire set on a 1998 Dodge Stratus ES 2.5L, you must first disconnect the wires under the instrument panel. You would then hook it up in the exact same order.
A 1998 Ford Windstar has the Electronic Distributorless Ignition System ( EDIS ) so there is no distributor . It uses ( 1 ) coil pack that has ( 6 towers ) for the spark plug wires
How do you remove ignition tumbler 1998 ford Mustang?
Either your starter is shot, or you need a new ignition system. Also check and make sure your battery is not dead.
Follow the plug wires form the spark plugs. If they go to a cylinder then that's the cap. It should unbolt out or have fasteners. It could be a DIS distrbutorless ignition system. Meaning the plug wires go into a square block which is the ignition coil assembly. These systems do not have a cap and rotor.
The 1998 Toyota ignition coil is located on the firewall, in the engine compartment. The ignition coil can be found on the passenger side of the firewall.
I'm not a mechanic / technician but the ( 1998 ) Lincoln Town Car , 4.6 V8 has the Coil On Plug ( C.O.P. ) ignition system with ( 8 ) individual coils
(1) defective spark plug (2) defective ignition wires (3) defective distributor.
On a 1998 Ford Expedition : The 4.6 liter V8 has the Electronic Distributorless Ignition System ( EDIS ) and it has ( 2 coil packs ) along with the ( 8 spark plug wires ) ------------------------------------------------------------------------------------------------ The 5.4 liter V8 has the Coil On Plug ignition system and has ( 8 ) individual coils
change plug wires on 1998 isuzu hombre 2.2
On a 1998 Ford Windstar , the 3.8 ( and 3.0 ) have the Electronic Distributorless Ignition System ( EDIS ) so there is no distributor * they use ( 1 ) coil pack that has ( 6 towers ) where the spark plug wires connect
Begin by removing the wiring harness from your 1998 Chevrolet Suburban ignition module. Remove the ignition module retaining screws. Reverse the process to install your new ignition module.
The Aurora has a VATS ignition and either the contacts in the ignition lock are bad, the wires from the lock to the computer are broken or the VATS chip in your key is dirty or the contacts in the ignition lock is dirty and not making connection with the chip in the key.
Possible problems: 1.Check the firing order of your ignition wires. 2.There could be a water inside of one of the spark plug socket,remove the spark plug and insert a clean dry cloth inside to dry-up the water.
Begin by removing the retaining ring at the top of your 1998 BMW ignition switch. The ignition switch will slide out. Remove the wiring harness.