0
Why does the oil light come on in a 97 Dodge Stratus when it's at a stop and go off when you step on the gas?
Wiki User
∙ 17y ago
your oil pressure is lower when the vehicle is idling, could be low do to lack of oil, when was the last time the oil was changed? could also be fuel in the oil. any other problems? I've also had this problem in a 1998 Stratus, and the oil is not low. I'm suspecting the oil pump is going bad, but I haven't looked in the manual yet to find where it is/what it runs off of. -jb9081
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
How do you change the fuel filter on a 1998 Dodge Stratus SE step by step for a female novice?
Not a job for a Novice as you have to lower the fuel tank as it is ontop of it ......
How do you install an alternator on a 2003 Dodge Stratus?
The 2003 Dodge Stratus came optionally equipped in a 3.0L V6 engine. The first step is the disconnection of battery cables. Second, the serpentine drive belt can released and removed. Last, the two bolts holding the alternator to engine mount can be removed and replacement. The OE alternator for the 3.0L application is AC Delco #3341420.
How do you program a 2002 dodge stratus key fob?
I'm pretty sure the dealership has to program the fobs. I programmed my key using the instructions in the owner's manual. They're really simple if you follow them step-by-step, but I'm not sure if the instructions for the fob are in there.
How do you replace power window switch 2004 dodge stratus?
To replace the window switch in your 2004 Dodge Intrepid you need to remove the door panel. Once the door panel is removed there are two T-20 Torx screws that hold the switch to the door panel. I have included a step by step auto repair video below, that shows how to accomplish this.
How do you turn off service engine soon light 2004 dodge stratus?
First step is to have the code read by a reader. Whatever the code refers to needs attention. Try removing the negative terminal from the battery, waiting 10 minutes and putting it back on - see if it goes away. If it stays on, or reappears later, you have an issue somewhere.
How do I get Step by Step instructions for changing a water pump on a 2000 Dodge Stratus?
Putrchase a repair manual for this car at most auto parts stores.Putrchase a repair manual for this car at most auto parts stores.
What has the author Jane Dodge written?
Jane Dodge has written: 'Step-by-step new macrame'
Why does your brake light come on when you step on the brakes in your 98 silverado?
Light on dash? Check fluid level in master cylinder
How do you replace a oil pump in a 2004 dodge stratus?
i think it is attached to crank shaft behind it's sprocket. I took 4 screws that attache oil pump to engine but it wont come out cause crankshaft sprocket is in the way. do i have to pull the sprocket with 3 jaw puller? seems like I can't find any useful info.Waynes manual skips this step :(
How do you change wiper blades on a dodge stratus?
The first, important step is to buy the correct-fitting replacements. Dodge changed the wiper configuration over the years as well as on different "trim's", for example sedan vs. coupe.Additionally, the installation process is simple. The replacement wiper blades will come with step-by-step, illustrated instructions and once you have the instructions and the wiper blades/arms in your hands and in front of you, it will all make better sense and will an easy maintenance task. Essentially, the old blades snap right off easily and the new blades will snap back on just as easy. Very simple and takes 5-15 minutes usually not requiring any tools.Also on a 2002 -2006 stratus the blade sizes are,driver side 24",passenger side 21".On 1995-2001 wipers size is 22" for both.
How do you change wiper blade on 1997 dodge ram truck?
The 1997 Dodge Ram Series Pickup takes 20" replacement windshield wiper blades on both sides front. For installation, the replacement wiper blades will come with simple-to-follow, step-by-step, illustrated instructions
2001 dodge stratus 2.4 dual cam head bolt torque Spec?
4 steps. step 1 starting with the front center bolt then rear center bolt continue in a clockwise direction torque all to 25 ft.lbs. step 2 repeat at 50 ft. lbs step 3 repeat again to 50 ft.lbs step 4 same pattern additional 90 degrees to each bolt.
