Want this question answered?
To program a Toyota Camry key first open the driver's side door and close all other doors. Insert the key into the ignition two times within five seconds. Close than open the driver's side door. Put your key in ignition and pull it out quickly. Close driver's door and open it. Put the key back in the ignition, close the door and put the key to the "on" position. Remove from ignition than listen for the door locks to cycle.
driver side, under hood, close to battery
Yes, an example is an automobile's ignition coil, which is energised from the battery, via the contacts within the distributor. The contacts open and close, supplying the ignition coil with pulsating current.
It is mounted on the driver side inner fender close to the battery.
Follow instructions Close all doors, trunk, and hood. The alarm must be disarmed. The key needs to be removed from the ignition switch. Open the trunk and leave it opened. Open the driver's door and sit in the driver's seat. Close the driver's door. Cycle the ignition switch five times between the OFF position and position 2. The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started. The ignition switch cycling must be performed within 10 seconds. The above sequence must be performed within 45 seconds. Open the driver's door and remain seated in the driver's seat. Close the driver's door. Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered. Open the driver's door and exit the vehicle, leaving the door open. Close the trunk. Close the driver's door. The LED will turn off and the siren will chirp twice. The initialization procedure is now completed. -------------------------------------------------------- Follow instructions Close all doors, trunk, and hood. The alarm must be disarmed. The key needs to be removed from the ignition switch. Open the trunk and leave it opened. Open the driver's door and sit in the driver's seat. Close the driver's door. Cycle the ignition switch five times between the OFF position and position 2. The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started. The ignition switch cycling must be performed within 10 seconds. The above sequence must be performed within 45 seconds. Open the driver's door and remain seated in the driver's seat. Close the driver's door. Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered. Open the driver's door and exit the vehicle, leaving the door open. Close the trunk. Close the driver's door. The LED will turn off and the siren will chirp twice. The initialization procedure is now completed. --------------------------------------------------------
To program a new keyless entry remote Toyota, first insert the key into the ignition and remove twice in 5 seconds. Second, close and open driver door twice in 40 seconds. Third, insert the key and remove it again from the ignition. Then close and open driver door twice in 40 seconds. Programming is now complete.
You should do a BSI reset. Put the driver's window down, lift the bonnet and ensure all equipment is switched off. Ensure all doors are closed and remove key from the ignition. Wait for 3 minutes, disconnect the vehicle battery and wait 15 seconds. Reconnect the vehicle battery, wait a further 10 seconds (do not open doors.). Switch on the side lights through the driver's window. Switch on the ignition and check system's functionality. Hold lock button on key down for 10 seconds. Remove key open & close door test central locking system. Start the engine and complete the system's check.
if clicking but not starting dead battery if it starts it's one of the many relays that open and close during startup
The horn is located on the driver side of the engine, real close to the battery. No. It's on the passenger side next to the rad.
That's a security issue, if your wheel locks and you cant turn the key for ignition, get in driver seat put key in ignition close the doors, lock yourself in the car, and try to start the car.
From my 07 manual:Start the engine. Push down and hold the driver's window switch until the window is fully open.Pull and hold the driver's window switch to close the window completely, then hold the switch for about 2 seconds.
on the 6 cyl it is either mounted on the distributor or on the driver side of engine compartment close to the firewall. If it is not distributor mounted it will be in the middle of a large alloy heat sink.