0
Why does your brake pedal depress with little resistance the first time but the second time it feels normal you replaced pads and rotors on the back then bleed them?
Wiki User
∙ 15y ago
It sounds like you still have a little air in the brake lines. You probably need to bleed them again. Or you have the pads installed improperly.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is normal systemic vascular resistance?
The resistance the heart has to pump against
Is it normal to feel confuse irritable and depress after 3 months of quitting lexapro?
These feelings, when they persist or are severe, are never "normal" and should be discussed with a healthcare provider.
I just replaced the tming chain on Chevy 350 should new one have any slack on one side?
YES. but very LITTLE is normal.
How do you set your BODY GEAR watch?
Here are the instructions for a Body Gear Kids' Sports Watch: 1. NORMAL TIME READING Hour, Minute, Second and Weekday, Depress S1 to show month, date and weekday Depress S2 to show Alarm Time Depress S4 to turn on the EL-light 2. NORMAL TIME SETTING Depress S3 three times second flashing reset by S1. [Display: (TU) mark flashing]. Then select the setting modes by S2 and advance by S1 with the procedures as following:- 1st press: set the minutes 2nd press: set the hour. [during setting 12/24 hours can be selected by 1 day cycle. i.e. AM/PM in 12 hours format or H in 24 hours format]. 3rd press: set the date. 4th press: set the month. 5th press: set the weekday. Then press S3 Once for return to normal time display. 3. CHRONOGRAPH Depress S3 Once to show chronograph mode [marks flashing: (SU), (FR), (SA)]. Depress S1 for start counting with (SA) and (SU) marks flash stop by depress S1, colon not flashing but (SU), (FR), (SA) marks flashing. To reset by depress S2. Max. range up to 23hr, 59min, 59sec. 4. LAP TIME In chronograph mode, depress S1 to start counting and stop by S2 colon flashing with the lap (SU), (TH), (SA) mark flashing. To reset by depress S1 then depress S2 twice. Depress S3 Once for return to normal time display. 5. ALARM TIME SETTING Depress S3 Twice for alarm mode with hour flashing, advance by S1. [Alarm mark On.] Depress S2 Once, minutes flashing advance by S1. Depress S3 Once, for return to normal time display. Alarm On/Off by hold S1 and depress S2 simultaneously in normal time display. Alarm stop by depress S2 Once. Please note that there is a snooze feature by pressing S1 during the alarm sound. Once activated the snooze will sound the alarm 5 minutes later. 6. ALARM TEST Depressing S1 and S2 simultaneously for alarm test. 7. HOURLY CHIME It can be enabled or disabled by holding S2 then depress S3. All the day marks appears when the Chime enabled. [In normal time display] 8. BATTERY CR2016 or EQUIVALENT 391/392 or EQUIVALENT CR1220 or EQUIVALENT CR1618 or EQUIVALENT LR1130 or EQUIVALENT V389 or EQUIVALENT CR2025 or EQUIVALENT (Note, these are different size batteries and must be for different watch sizes. Check which one your watch uses before buying a replacement battery.) Depress S4 or S5 for Light.
What happens to current flow when the resistance is higher than normal?
For a specific voltage, current flow is inversely proportional to resistance.
The normal way for most slaves to express discontent was?
Slaves expressed discontent through various means such as sabotage, work slowdowns, feigning illness, and occasional violent rebellions. They also used subtle forms of resistance like breaking tools, feigning ignorance, or disrupting work routines to resist the dehumanizing conditions of slavery.
How does a shark behave when it is sad?
it swims a little slower than normal it swims a little slower than normal it swims a little slower than normal
What is the normal process of putting a manual car in neutral?
The normal process for putting a manual car in neutral is to first completely depress the clutch. After the clutch is fully depressed then it is safe to shift the gear stick into neutral.
The engine light came on after you had the timing belt replaced Is this normal?
No problem
Which instrunment is used to measure the resistance to earth?
A normal ohmmeter (or multimeter with this feature) should do it.
What is thermotolerance?
Thermotolerance is a living organism resistance to temperatures causing death in normal conditions.
How is insulin resistance prevented?
Insulin resistance is prevented by maintaining a normal weight, eating a balanced diet, and keeping up a regular program of aerobic exercise.
