0
Why eccentric bottom tapping is named eccentric in electric arc furnace?
Wiki User
∙ 10y ago
off center
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is an electric desalter?
an electric desalter is one which uses a high electric potential to separate the salts present in the crude. it is a horizontal drum .it forms an emulsion with crude an emulsion is a mixture of crude and water.water added to the crude acts as an solvent for dissolving the salts present in the crude .once these salts are properly dissolved the electric charge breaks these salts into charged ions and form a dipole .water along with salts settle at the bottom and the crude overflows to the fractionation column
Does anyone have a wiring diagram for a Hyster electric forklift model E65XM2-40 Thanks, Ken.?
You can request a wiring diagram from Hyster Company. Just visit their website at http://hyster.com/americas/en-US and click on Contact Us at the bottom of the page.
Rate at which electrical energy is converted to another type of energy?
The rate at which an appliance takes energy from the electrical outlet and spinsthe electric meter is the "power" shown on the data label, usually on the backor the bottom of the appliance.The rate at which it actually converts the energy into the form required to do itsjob is also a "power" figure. This one is always less than the power taken fromthe wall outlet, and is not always stated or marked on the appliance.A couple of cases where it is clearly stated:-- Microwave Oven: " 600 Watts of Cooking Power "The microwave oven is using perhaps 1,500 to 2,000 watts from the electric company,converting some of it into radio waves (with less than 100% efficiency), and delivering600 watts of microwave radiation to the cooking chamber.-- Blow Drier: " 1,250 Watts of Drying Power "The blow drier is using perhaps 1,500 watts from the electric company, anddelivering useful energy at the rate of 1,250 watts, in form of a hot coil anda strong little fan motor to blow air across the coil.But on an electric stove, furnace, blender, food processor, fan, telephone, TV,computer, vacuum, washer, dryer, etc., you can find the power consumptionmarked somewhere on it, but it's not clear exactly where that power goes.
What height do you fit electric sockets in UK?
The standard height is around 12" to 15" the bottom of the box above the floor but for the disabled you can install them higher but no more than 48" above the floor. Pick a height that will work for the disabled and install all of them the exact same height.
How do you properly ground an electric fence?
You need to have a grounding rod made of galvanized steel that is driven straight into the ground until only half an inch of bar is remaining above ground. The ground rod should be at least 6 feet in length. Drier land areas normally require a longer grounding rod, or more of them, spaced 10 feet apart. The ground rods themselves should be placed in [an] area[s] that are naturally permanently moist to have any effect. Then you have to run a grounding cable that is attached to the ground rod along the bottom or top of the fence (can be the top wire or bottom wire) all the way to the fence charger. This cable needs to be attached to the ground rod by ground rod clamps That grounding cable should be attached to that fence charger in order for the fence to be properly grounded. Check out the following links on tips and instructions on how to properly ground an electric fence.
Why eccentric reducers recommended for horizontal lines?
It is so that the inside bottom of the line can drain completely if required and no fluid or condensate will remain trapped. In other words the eccentric reducer keeps the bottom of the line straight.
How do you think the blast furnace got its name?
the blast furnace got its name , because its bottom which is called a furnace blows hot air to go up.
How is iron removed from a blast furnace?
Iron is removed from a balst furnace, it melts as it seeps down to the higher temperatures at the bottom of the furnace from where it is tapped off. Hope that helps.
How is slag collected from a blast furnace?
iron is collected from blast furnace by drilling the taphole.Taphole is a hole drill and plug after cycle of time located in blast furnace bottom.
What is the bottom of a chimney?
A furnace or fireplace or the ash dump box.
Someone in your class keeps tapping the bottom of your foot?
they like you or want to annoy you
Flat side should be top or bottom for eccentric reducer in vacuum line?
Doesn't matter
How do you make a ds run faster than normal?
keep tapping on the bottom screen with your pen
Is AOD furnace used in non-ferrous alloy?
AOD furnace is not used in non-ferrous alloys. AOD = Argon-oxygen process. - AOD process is a widely used method for making quality steel. The charge is melted in an electric furnace and after a slag off it is transferred to the AOD vessel for refining, alloying and final finishing. - The tuyers arranged in a semi circle around the side near the bottom blow process gasses inside the AOD vessel. - The slag is reduced and final additions are made after a preliminary analysis. - The vessel is turned down for sampling, temperature measurement, slag off and tapping and the heat is poured into the ladle for further use. In AOD process there is continual thorough stirring of heat. - The method provides a very close control of heat chemistry. - Computer control ensures repetitive uniform melting and refining. - AOD refining reduces the hydrogen content to about half the value in electric furnace melting. - There is minimal loss of chromium to the slag.
Why is blast furnace tapered from bottom of the furnace?
it is tappered to accomodate the gradual volume expansion of the solid charge as it descends through zones of Stack,from top to bottom in the stack the temperature gradually increases and we need to ascertain smooth burden descent.
Extraction of lead from galena by heating process?
First: Roast the Galena in a blast furnace for 30 minuets. Second: Add Carbon to the blast furnace to remove impurities. Third: Tag off your lead from the bottom of the blast furnace.
Should the return at the bottom of the wall be open or closed when the furnace is on?
Open, that`s where the cold air is.
