0
in dc circiuts only resistors are responsible for voltage drop. where as in ac circuits inductances and capacitances are also responsible for voltage drop in addition to that of ressistors
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is line voltage or phase voltage mentioned on transformer nameplate?
It depends how they are connected. If they are connected between line conductors then they are measuring line voltages. If they are connected across phases then they are measuring phase voltages.
What is voltage regulation formula?
The formula for voltage regulation is: Voltage Regulation = (V_no-load - V_full-load) / V_full-load * 100% where V_no-load is the voltage measured at no load, and V_full-load is the voltage measured at full load. The result is expressed as a percentage.
What is a line to line voltage?
In a 3 phase system, the voltage measured between any two phase is called line to line voltage.And the voltage measured between line to neutral is called phase to neutral (line to neutral) voltage.AnswerThere is no such thing as a 'phase-to-phase' or a 'phase-to-neutral' voltage. The correct terms are 'line-to-line' and 'line-to-neutral'.The voltage between any two line conductors is called a line voltage.In a three-phase, three-wire, system, the line voltage is numerically equal to the phase voltage.In a three-phase, four-wire, system, the voltage between any line conductor and the neutral conductor is called a phase voltage. The line voltage is 1.732 times larger than the phase voltage.
What is the difference between line voltage and phase voltage?
The three 'hot' conductors supplying electricity to a three-phase load are called LINES, not 'phases' (although unfortunately the term 'phase' is widely, but incorrectly, used in the field). Phases exist between line and neutral in star, or wye, connected systems, and between lines in a delta, or mesh, connected system. Accordingly, the term 'phase to phase' is quite meaningless. A line voltage, therefore, exists between any two lines. For a star (wye) connected system, a phase voltage exists between any line and the neutral conductor. For a delta (mesh) system, a phase voltage is exactly the same as a line voltage.
Why might the unloaded output voltage of a transformer be higher than its rms of 12.6v?
Because the windings of transformers have resistance, the primary and secondary currents will cause voltage drops. To compensate for the drops, the transformer may have been designed to have a higher than specified output voltage when there is little or no output current. The no load output voltage typically is only slightly greater than the specified voltage. Before measuring the output voltage, measure the input (line) voltage. If it is not as specified for the transformer, calculate its effect on the output.
The voltage present in a power grid line is more than?
The voltage present in a power grid line is more than enough to kill you.
Is line voltage or phase voltage mentioned on transformer nameplate?
It depends how they are connected. If they are connected between line conductors then they are measuring line voltages. If they are connected across phases then they are measuring phase voltages.
What is voltage regulation formula?
The formula for voltage regulation is: Voltage Regulation = (V_no-load - V_full-load) / V_full-load * 100% where V_no-load is the voltage measured at no load, and V_full-load is the voltage measured at full load. The result is expressed as a percentage.
Is industry self regulation better than government regulation for automobile safety?
It is not a matter of better or worse; both are needed to have an effective system of safety in the workplace and the marketplace.
Why is phase voltage not twice line voltage?
Line to line voltage is not the same as line to neutral voltage because line voltages are 120 degrees apart. They are related by: Line to neutral voltage * tan (120 degrees) = Line to neutral voltage * 1.73.Additional CommentFor delta-connected systems, the line voltage is the same as the phase voltage.For wye-connected systems, the line voltage is larger than the phase voltage by a factor of 1.732. The reason for this is as follows:Because any two phase voltages are displaced from each other by 120o, they must be added vectorially, not algebraically, to find the line voltage. As the above answer points out, this means that the relationship between the two is the square-root of 3, or 1.732.
What is voltage regulation?
Voltage regulation:(from point of view of electrical machines or generator): It is the change in voltage in between the full loaded and no loaded condition. When there are no loads connected the terminal voltage is equal to the generated voltage in the generator. But when load is connected the terminal voltage is found to be lass than the no loaded condition, due to armature resistance leakage reactance.This phenomena is expressed as, % reg=(Vnl-Vfl)/Vfl * 100%.Which is Voltage regulation. ************************************************************ An ideal voltage source has zero internal impedance. A practical one, even a good one, has internal impedance. With no load on the source, the terminal voltage will have a given value. Once a load current is drawn there will be a voltage drop across the source's internal impedance, and the terminal voltage will therefore drop. The higher the load current, the higher the voltage drop. A regulator circuit, added after the source, can counter the effect of the source's impedance and maintain an output voltage which is more constant than the source itself can achieve.
What is a line to line voltage?
In a 3 phase system, the voltage measured between any two phase is called line to line voltage.And the voltage measured between line to neutral is called phase to neutral (line to neutral) voltage.AnswerThere is no such thing as a 'phase-to-phase' or a 'phase-to-neutral' voltage. The correct terms are 'line-to-line' and 'line-to-neutral'.The voltage between any two line conductors is called a line voltage.In a three-phase, three-wire, system, the line voltage is numerically equal to the phase voltage.In a three-phase, four-wire, system, the voltage between any line conductor and the neutral conductor is called a phase voltage. The line voltage is 1.732 times larger than the phase voltage.
Which is better Constant Voltage Transformer or servo stabilizer?
A CVT (Constant Voltage Transformer) is always better than a Servo Stabilizer. But a CVT is costlier than a Servo Stabilizer of same rating.
Why peak voltage of the load is smaller than the voltage from the transformer output?
The voltage appearing across a load is always smaller than the no-load voltage of any voltage source -e.g. batteries, generators, or transformers. In simple terms this is because all these voltage sources have internal resistance or impedance which results in an internal voltage drop when the source delivers a load current. The resulting voltage, therefore, is always the difference between the no-load voltage and the internal voltage drop. A measure of the difference between a source's no-load and full-load voltage is termed its 'voltage regulation'.
What can be better than a line graph?
Two line graphs?
What voltage should be used when making three phase calculations?
With a three-phase system the voltage quoted is the line-to-line voltage between any two live lines. To find the line-to-neutral voltage divide by 1.732 which is sqrt(3). The power supplied from each phase is the current times the line-to-neutral voltage (times the power factor if less than 1). To find the total power when the currents are equal, multiply by 3.
What is phase voltage and line voltage in star connection?
The conductors that connect a three-phase supply to its load are called 'line conductors' or, more simply, 'lines'. The individual generator stator windings, transformer winding, or loads are called 'phases'. Lines and line terminals are identified by colours, letters, numbers, or combinations of letters and numbers. For example, A-B-C. Phases are identified by using the letters assigned to the line terminals between which the phases are connected, e.g A-B, B-C, and C-A. Voltages measured between lines ('line-to-line') are termed 'line voltages', and currents that pass through the lines are called 'line currents'. Voltages measured across a generator's windings, transformer windings, or individual loads, are called 'phase voltages', and the currents that pass through these are called 'phase currents'. For a three-phase, three-wire, system, the phase- and line-voltages are numerically-equal to each other. For a three-phase, four-wire, system, the line voltage is 1.732 times larger than the phase voltage.
