Be the first to answer!
Automatic transmission? 2 vehicle will shift only from 1st to 2nd gear 3 vehicle will shift from 1st to 2nd to 3rd gear 4 vehicle will shift from 1st to 2nd to 3rd to 4th gear
when talking about a motorcycle, the traditional location for neutral is between 1st and 2nd gear. you shift all the way down to 1st while lightly moving the motorcycle back and forth. you then lightly tap the gear lever up without entering 2nd gear. vualla, your in neutral.
depending on the bike and surface you can start in 1st, 2nd and 3rd but most common gear to use is 2nd gear
1st gear down 2nd gear up 3rd up 4th up 5th up N between first and 2nd gear
Gear Ratios (:1)1st Gear 3.062nd Gear 1.633rd Gear 14th Gear 0.7Reverse 2.29
on a 2000 intrigue; car does not shift into 3rd gear or 4th gear. 1st 2nd gear ok
Push the car with the clutch in, right? 2nd gear for smooth and 1st gear for most people!
What is your question? This question makes no sense.
There is no drive in a standard transmission car. In most cases you will have reverse, neutral, 1st gear, 2nd gear, 3rd gear, 4th gear, and 5th gear.
alot of torque, try letting off the clutch smoothly while adding a steady amount of gas.
If your Kia Sephia doesn't move in drive, but does move in 1st and 2nd gear, you have a problem with the transmission. Sometimes this is just an issue with the linkage and can be repaired easily.
you have burnt out the 3rd. gear and overdrive. you will have to have it rebuilt or replaced.
Between 1st and 2nd gear.
1st 2nd 3rd 4th 5th & Reverse gear
It stands for: Park=P Reverse=R Neutral=N Drive=D 1=1st gear 2=2nd gear 3=3rd gear
Reduction ratios: 1st gear 2.45:1 2nd gear 1.45:1 3rd gear 1:1 Overdrive 0.69:1 Reverse 2.22.1
clutch gone try putting into gear then start engine be ready to shut engine off
Need a new gearbox. You get a grinding noise only in first gear when you accelerate fast . second gear and the rest should be fine.
hi i got a Honda accord 95 a just put a new clutch kit in it clutch pressor plate and new beering and now when i downshift in 2nd gear it shakes a couple time tehn it stops what does that shaking ??
1st gear is for the slowest speeds , up to 15 mph or very steep hills 2nd gear is for speeds up to about 30 mph or hills, third gear is from 30-50mph, 4th and higher is for speeds over 55mph.
no you start in 1st gear then 2nd hold around 4000rpms depending on what you have for a engine
From page 46 of a 1966 Volkswagen Owners Manual, the gear ratios are: 1st gear 3.80:1 2nd gear 2.06: 1 3rd gear 1.26:1 4th gear 0.89:1 Reverse 3.88: 1
I have the same issue....bought it, the Auto 4WD worked now it stays in 2HI. If I put it in 4 hi or 4 lo it goes into a mode where my tranny doesnt get out of 1st or 2nd gear meaing my max speed is like 40 MPH before it starts shaking.
For Pulsar, Apache and Karizma and Honda (bikes > than 135cc) the 1st gear is down...den all upwards(2,3,4,5)...the neutral lies b/w the 2nd and the 1st
1st- 2.52:1 2nd- 1.52:1 3rd-1:1
Asked By Wiki User
Copyright © 2021 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.