It fails. Paint is developed using tens of millions of dollars and the formulas are pretty exact. On really hot days, you can add a "little" Flo Troll to help keep the streaks down and have it not set up as fast. That's it, no water or anything else.
I hardly ever thin latex. I find that reduces its coverage. If you go to a thicker roller and don't press hard on it ,that may help.
Thinning latex is done when spraying.
No, you use water to thin latex paint. Thinner is for oil based paint.
Mixing a solvent into a latex typically ruins the product. Expected result is the latex paint turning into gel.
If you are using latex, thin with water. If using enamel, thin with paint thinner.Always read instructions on the can. They always say what to thin it with.
You can mix water into most latex paints up to a point. Usually eight ounces to a gallon. A better alternative is to add a latex paint additive, like Flotrol, that is made out of acrylic resin, that doesn't degrade the paint.
What do you mean? Yes, paint on wood trim is typically latex these days. Some older homes may still have alkyd (oil), though. To find out for sure, put a little nail polish remover on a cotton swab and rub it on the paint in an inconspicuous location. It it gets soft and starts to come off, it's latex. Either way, sand it lightly and recoat with the same type of paint and you're good. If you're asking about bare wood, DON'T USE LATEX! The water will swell the grain of the wood. Use an oil primer that is made to take latex topcoats.
Yes it can, but not very much.
No, you use water to thin latex paint. Thinner is for oil based paint.
Mixing a solvent into a latex typically ruins the product. Expected result is the latex paint turning into gel.
If you are using latex, thin with water. If using enamel, thin with paint thinner.Always read instructions on the can. They always say what to thin it with.
You can mix water into most latex paints up to a point. Usually eight ounces to a gallon. A better alternative is to add a latex paint additive, like Flotrol, that is made out of acrylic resin, that doesn't degrade the paint.
It looks and is very thin. Often 2-3 coats are needed.
What do you mean? Yes, paint on wood trim is typically latex these days. Some older homes may still have alkyd (oil), though. To find out for sure, put a little nail polish remover on a cotton swab and rub it on the paint in an inconspicuous location. It it gets soft and starts to come off, it's latex. Either way, sand it lightly and recoat with the same type of paint and you're good. If you're asking about bare wood, DON'T USE LATEX! The water will swell the grain of the wood. Use an oil primer that is made to take latex topcoats.
If you really want to ... yes. It might cause some issues later but should work for the most part as long as you apply a thin layer of paint. Acrylic house paint is normally a latex paint, so there should be no problem painting over a latex with acrylic. The only exception is if it is a solvent based acrylic silicone type paint. In this case, the coating will melt the latex paint, and if overworked while rolling, mix on the surface, which is normally a driveway or floor, discoloring the top coat.
You could, but if you have some 100% acrylic solid stain, you would get better results since you wouldn't need to thin it nearly as much as a paint. If you have to use paint, instead of diluting with water, dilute with a latex paint conditioner like Flo-trol as much as possible. Water will break down the binder if used to over thin the paint causing the solids to powder over time. Even better, use fabric dye unless you are trying to achieve a design that requires paint.
Yes, the thinner for latex paints is water, but you should never thin latex any more than about 5%, 10% at the very most.
Yes, the thinner for latex paints is water, but you should never thin latex any more than about 5%, 10% at the very most.
NO