0
Why the metal strip should be flat or wire be kink free in screw gauge?
Wiki User
∙ 11y ago
if the strip will flat we can measure its thickness easily but if it is not flat i.e. its surface is irregular then it will thick only from some points and its other area will
be thin and we cannot measure its thickness easily.same is the reason for wire.
Wiki User
∙ 11y ago
Areeba
to measure its thickness easily
Add your answer:
Earn +20 pts
What is two strips of different metals welded together causing the strip to bend when heated?
That's a "bi-metal" or "bi-metallic" strip.
How does a Strip Heater work?
it works by heating the 2 metal strip of metal and then you put the acrylic on them then wait for 2mins then take the acrylic carefully off then start bending it into your favorite shape
Can one produce energy with a bi metal strip when heated?
Yes
When a bimetallic strip is heated it bends toward the metal with the thermal expansion?
... smaller ...
Why does a bimetallic strip bend when heated?
A bimetallic strip bends when heated because it is composed of two different types of metal. The different metals form the two sides of the strip expand and contract at different rates when subjected to a temperature change. When heating a bimetallic strip, one side of the metals expands faster than the other, making it longer. Because it is bonded to the other metal, it cannot expand in a straight line. The only way the two metals can stay bonded while expanding at different rates, is for strip to bend, one side becoming longer than the other.
What is the advantage of a posidrive screw over a slot headed screw?
A posidrive screw stays centered over the driving tool. On Slotted head screws, the screwdriver can slip easily out of the groove. A very nice kind of screw is the "TORX" head screw. With the proper torx bit, they cannot slip or strip easily while screwing them into wood or metal.
How do I keep my cordless screwdriver from stripping screw heads?
The best thing to do is to not drill the screw heads to far down, since it will have a tendency to strip the screw heads, you should also consider making sure you item is prefectly mounted due to the problems of the screw.
How do you attach a banana to the ceiling?
Take a hook like a command strip, screw it, tape it, or somehow atatch it to the ceiling, then peel tiny strip of the banana and screw the it through the hook
What is the strip of land separated from Israel by a metal fence?
Gaze strip
What gauge is the black wire with red strip ground from the alternator?
That particular wire is usually 10 gauge.
What is the metal strip called that holds down a rug?
That can be the carpet edging strip, the fastening strip, carpet plating strip for a few names.
How long will the metal strip be 5.65 cm 6.70 cm and 4.32 cm?
The total length of the metal strip is 16.67cm or 6.56 inches.
What is the metal strip called that covers the edge of a carpet at a doorway?
the metal strip or anything for that matter that goes at the bottom of doorways is called a threshold.
How do you field strip an Eastern Arms Company Single Shot 16 gauge shotgun?
There may be a screw under the fore end. If so, remove it. If there is no screw, or once the screw is removed, the fore end should pull away from the barrel, at its front. It may take some effort and may be held in place by spring tension. Once it comes loose, the barrel can then be opened normally, and will dismount from the receiver pivot. To reassemble, set the barrel in place, set the fore end against the receiver, and snap it back up against the barrel. Then replace the screw if there is one.
Why does a bi-metal strip bends?
A bi-metal strip consists of two metals that expand by different amounts when the temperature changes, so it will bend when heated.
Is a fuse made out of glass?
(A+) a strip of metal inside
Where is the fuel pump on a 1999 Kia Sportage?
in the tank the is an access panel in the trunk area that you should be able to get to it from warning do not strip on snap the screw heads off you will have to drill and tap them out if you do
