0
The emitter resistor is connected to ground(in the case of an rc coupled amplifier).Also input signal applied at the base is grounded.Then the emitter resistor forms a feedback to the input signal (through the ground return path).So emitter resistor is also called feedback resistor.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can you use resistance in place of diode in clipping circuits?
no we not use resistance in place of diode.
What is the effect of emitter resistance in common emitter amplifier?
The gain of a common-emitter amplifier is collector resistor divided by emitter resistor, or hFe, whichever is less. Since hFe depends on temperature, designing the amplifier to be dependent on resistance ratio makes it more stable. As such, the emitter resistance serves to stabilize the amplifier.
What will happen to voltage divider circuit if emitter resistance is greater than collector resistance?
The gain of a class A, common emitter BJT amplifier, a fairly standard configuration, is defined as collector resistance divided by emitter resistance, or as hFe, whichever is less. Assuming that we are operating in a linear mode, and hFe is not a limiting factor, then the emitter resistance being greater than the collector resistance simply means that the gain is less than one.
What is the effect of no emitter resistance on common emitter amplifier?
Limit current through emitter, Often the resistance is the load itself. So the restatnce limits current on what otherwise would act as a voltage follower.
True or false a high resistance between the collector and emitter when a transistor is switched off?
yes , it has high resistance between collector and emitter on the off state.
Why Common Emitter Configuration is most commonly used in amplifier circuits?
the common emitter configuration is most widely used in amplifer circuits because of its high voltage,current & power gain.the common emitter configuration is most widely used in amplifer circuits because of its high voltage,current & power gain.
Can you use resistance in place of diode in clipping circuits?
no we not use resistance in place of diode.
Why would there be a gain when you add the emitter capacitor to a circuit board?
A capacitor has lower resistance (impedance) as frequency increases. Adding an emitter capacitor effectively lowers the emitter resistance as frequency increases. Since gain in a typical common emitter amplifier is collector resitance divided by emitter resistance, this decrease in emitter resistance will increase gain as frequency increases.
What is the effect of emitter resistance in common emitter amplifier?
The gain of a common-emitter amplifier is collector resistor divided by emitter resistor, or hFe, whichever is less. Since hFe depends on temperature, designing the amplifier to be dependent on resistance ratio makes it more stable. As such, the emitter resistance serves to stabilize the amplifier.
What is swamping resistance?
(Electronics) Resistor placed in the emitter lead of a transistor circuit to minimize the effects of temperature on the emitter-base junction resistance and its resistance is called swamping resistance.
Why the base bias Q-point in transistor circuits changes with temperature?
why we use base resistor in emitter bias
What is the function of emitter bypass capacitor in common emitter amplifier?
The emitter bypass capacitor in a common emitter amplifier will have less resistance as the frequency increases. Since gain in this configuration is collector resistance divided by emitter resistance (within limits of hFe), the gain will thus increase for higher frequencies, making this into a high pass filter.
What will happen to voltage divider circuit if emitter resistance is greater than collector resistance?
The gain of a class A, common emitter BJT amplifier, a fairly standard configuration, is defined as collector resistance divided by emitter resistance, or as hFe, whichever is less. Assuming that we are operating in a linear mode, and hFe is not a limiting factor, then the emitter resistance being greater than the collector resistance simply means that the gain is less than one.
What is the effect of no emitter resistance on common emitter amplifier?
Limit current through emitter, Often the resistance is the load itself. So the restatnce limits current on what otherwise would act as a voltage follower.
Why emitter resistance RE is used?
for stability
What is use of capacitor Ce across emitter resistance?
It can be used as a feedback and to ground unwanted signals and frequencies
True or false a high resistance between the collector and emitter when a transistor is switched off?
yes , it has high resistance between collector and emitter on the off state.
