0
I'll assume you've tested to see if it's screwed on too tight *8-P
Hold the bottom base in place and unscrew the agitator. Nine times out of ten, something's caught in there gumming up the works.
If that's not it, put the washer on a 45 degree angle and look underneath. If you have the type with the belt drive, see if it'll move. if not, either it's wound too tight or the motor's got issues.
If yours doesn't have the belt, turn the washer on and see if the agitator motor is seized. If so, you're probably going to have to rebuild the motor (or have a professional do it.)
If the motor doesn't make the agitator spin, then you likely have a problem with your timer. They're pretty cheap, just replace it.
Hope that helps!
Additionally, there is a device that saves the washer from major damage, it is a two part couple; one part of couple is soft "rubber like" and the other is firm plastic. They join together and when stressed will shear. (It is used to protect the more expensive parts i.e. transmission and drive motor.) The couple is located above the transmission. usually it is a disc shaped item about 2-3 inches across and colored black or white. The part is very cheap and can be found at most appliance parts stores. Be careful when you dismantle the parts as some transmissions have an opening at the top and will leak a "nasty" lubricant if laid on its side. The most common cause for the failure is overloading the washer.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why does the agitator barely move in a washing machine?
An agitator that barely moves in a washing machine likely has too many clothes in the machine. Too many clothes constricts the agitator and prevents it from working as it should.
What happens to the velocity of the whirling washer when you shortened the string?
maybe if you spin the spring washer and its shortened the washer move is verry fast.
What will happen if a positively charge rod is brought near a metal washer?
Since a metal washer is neutral, the positive rod will make all the negatively charged electrons bunch up towards the front of the washer and nearer to the rod whereas the protons in the washer would repel from the rod and move to the back of the washer.
Why does your clothes come out of the washer steaming hot but you have put it on cold cycle?
The supply hoses are hooked up wrong. Hot is on the cold and since it rinses in cold, that means the last water in the tub is hot. Set the tempratue control to cold and start the washer. I bet the water is hot. Move it to hot and it will be cold. Just switch the hoses.
The working principle of a washing machine is?
A washing machine is a popular electronic home appliance, which is found in almost every household. In this fast age, a washing machine is highly popular because of its great utilities. It does the laundry quite fast, saving a lot of time and labor. It manages to do so, quite effectively and efficiently, as it follows a set wash process. A brief overview of how a washing machine works with respect to its different parts, is mentioned below.Basic Structure: The elementary components of a washing machine are agitator, inner and outer wash tub, electric motor and drain tube. A washing machine is also equipped with the valves, switches and timers to smoothen its working. Valves enable the passage of hot and cold water to the washing machine. The timer enables timed functioning. A typical washer has switches to adjust and control various functions. The speed of spinning, the special settings for different fabrics and the passage of hot and cold water are the functions monitored by the switches. Valves, switches and timers differ from model to model.These components have to be present in any type of washing machine, be it top-loading or front-loading. Different models of washers differ only in the positioning of these parts. There is a specific function assigned to each part.Inner Wash Tub: The process of washing starts in the inner wash tub. It involves the adding of water and detergent mixture to the clothes. The detergent contains many enzymes that work on clothes to clean them. Some such enzymes are protease, lipase, catalase and amylase. In the inner wash tub, the clothes are tumbled and moved to all sides by the agitator.Agitator: Agitator enhances the action of enzymes on clothes. An agitator is a plastic cylinder positioned at the center of the inner tub. Generally, an agitator is finned. Its finned structure aids it in its function. The function of an agitator is to move the clothing up, down, back and forth so that the clothing mixes well with the detergent. The inner wash tub also moves along with the agitator. This motion is repeated for a determined period of time. The agitator ensures thorough cleaning of the clothing. This cycle is known as the wash cycle. The inner tub has numerous holes. The centrifugal force pulls out wash water from the clothes and makes it move through these holes to the outer tub. The water gets drained out through the drain tube.Motor: In the wash cycle, the agitator and the inner tub are moved rhythmically by a powerful electric motor. In fact, it is the motor which accelerates the process of washing. Therefore, it is a very important component of a washer.Outer Wash Tub: The outer wash tub is stationary. Water gets pumped out from here. After the wash water has left, the inner tub is again filled with clean water. Agitator again works to tumble the clothing. This is the second cycle and is called the rinse cycle. The aim of this cycle is to discharge the detergent particles trapped in the washed fabric. On completion of rinsing, the machine again drains out water.Drain Tube: The purpose of the third cycle, which is called the spin cycle, is to remove out as much water as possible from the wet clothes. In all the steps, draining is carried out by the drain tubes. Once the water has been drained out, another electric motor comes to play. It agitates the inner tub at an extremely high speed. The centripetal force spins out remaining water from the fabric and expels it through the drain tube. This is a timed process. The clothing get reduced from saturated to merely wet. The cleaning of the fabric is done and it is ready to dry.Power Parts: Electric motors can reach high speeds quickly. In order to smoothen the start-up effects, washers are provided with a clutch. This clutch is similar to car clutches as it has the same standard drum-and-pad construction and functioning. Some units use a simpler method. They make use of drive belts. The drive belts slip on a pulley and fix gradually.
How much clothes to put in washing machine?
it depends on how big your washer is. you need to leave enough room for the agitator (the thing in the middle) to be able to move and move your clothes around. the water needs to be able to circulate through your clothes. if you put too many they won't get very clean and you could break your machine.
Why does the agitator barely move in a washing machine?
An agitator that barely moves in a washing machine likely has too many clothes in the machine. Too many clothes constricts the agitator and prevents it from working as it should.
What is the function of an SQL Loader?
The SQL*Loader is used to move files onto the Oracle database, for later access. The SQL*Loader is relatively simple to use and accepts many different types of files.
What happens to the velocity of the whirling washer when you shortened the string?
maybe if you spin the spring washer and its shortened the washer move is verry fast.
Can you use bleach to clean your smelly washer?
you can try - run an empty load with bleach added. Leave the top open between loads. A cup of white vinegar in the water will help also. If the smell remains, check under the agitator (unplugged) to see if something isn't caught in there. Also, move the washer out and clean the floor under it. Again, there might be something caught behind there. Leave the top open between loads.
What is a truss washer?
A truss washer is located on the crankshaft journal, It is to use to avoid the crankshaft to move forward or backward
Is it hard to move washer and dryer from bathroom to kitchen?
The washer is usually no problem, but you may run into problems with electrical supply and vent for dryer.
Is it hard to move washer and dryer from kitchen to bathroom in a condo unit?
Not at all
What will happen if a positively charged rod is near a metal washer?
Since a metal washer is neutral, the positive rod will make all the negatively charged electrons bunch up towards the front of the washer and nearer to the rod whereas the protons in the washer would repel from the rod and move to the back of the washer.
How do you locate the battery in the 1993 cutlass supreme?
Its under the washer fluid reservoir. Have fun with this one! You have to remove the support bar, the washer fluid reservoir, and move the air filter housing to get the battery out. Enjoy!AnswerIts under the washer fluid reservoir. Have fun with this one! You have to remove the support bar, the washer fluid reservoir, and move the air filter housing to get the battery out. Enjoy!
What will happen if a positively charged rod is brought near a metal washer.?
Since a metal washer is neutral, the positive rod will make all the negatively charged electrons bunch up towards the front of the washer and nearer to the rod whereas the protons in the washer would repel from the rod and move to the back of the washer.
What will happen if a positively charge rod is brought near a metal washer?
Since a metal washer is neutral, the positive rod will make all the negatively charged electrons bunch up towards the front of the washer and nearer to the rod whereas the protons in the washer would repel from the rod and move to the back of the washer.
