answersLogoWhite

0


Best Answer

alot of times if the fittings are close together the solder takes but doesen't get full penetration. over time the pressure of the water will push through the solder joint. the best thing to do is drain down the system and replace the leaky joints.

Answer

More than likely the plumber used too much flux or the pipes are undersized and the velocity of the water is causing erosion of the pipe.

Copper pipe corrosion can be caused by many things and many people have had the electric power company, every electrician, water treatment company and plumber they could find try to solve their problem with no luck. It is not caused by defective pipes. The fact that you indicate that you indicate that you are using your home every few weeks may actually be aggravating the problem by not having a regular flushing of the pipes.

The known causes are: 1.) Water condition - PH, mineral content or lack of, dissolved gases, microrganisms etc. 2.) Excessive flux used in the soldering of the pipes. 3.) Water velocity in the pipes - Copper gets a thin green coating this actually inhibits further corrosion. 4.) Undersized pipes for the velocity of the water - the green coating may be eroded causing further corrosion. 5.) Electrolysis - you are correct in assuming that the stray millivolts may have something to do with your problem. Stray voltages may be from improper grounding, of electrical, cable tv, phone. Or, leakages of current from water heaters, circulator pumps, well water pumps, boilers etc. 5.) Dissimilar metals used on the piping or in contact with piping can also be a problem we all have seen where a lazy hack has used steel strap to hang a copper pipe or used a black iron nipple because he was to lazy to head for the supply house when he was 1 short for the job.

Treaments out there include: Sacraficial Anodes for underground copper pipes. Epoxy coatings inside the pipe (I'm a sceptic on that one). Finding the right water treatment for your water (Do have it tested). Finding something electrically to cure your problem Repiping the house with a pipe such as Pex tubing.

If your house has well water with a chlorinator for the presence of iron, sulphur or bacteria, the chlorine over time can thin the walls of copper pipe and cause leaks as well.

Good Luck and I hope you don't have to open the wallet too far on this one!

User Avatar

Wiki User

7y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why would the copper plumbing in a 30-year-old house develop small leaks all within an inch or 2 of a soldered fitting?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What does c x c mean in plumbing?

Copper x copper, which means the fitting is sized for copper pipe and usually needs to be soldered unless it is a compression type fitting.


Is a soldered fitting better then a threaded fitting?

Depends on what you are doing. soldered is for copper water lines. Threaded can be for water, gas, or anything else.


What fitting will be used to connect the water service pipe to feed pipe for the house?

Water main coming into house usually 3/4" K copper pipe. Depending on local plumbing code, fitting usually is flared or soldered.


What does CXC mean in plumbing terms?

When it comes to a plumbing fitting, description CxC means the fitting is Copper by Copper, or the fitting is used to join two pieces of copper


What is finish plumbing?

Fitting of faucets etc.


What material used in plumbing fitting?

Brass is commonly used for most plumbing fittings.


What new profession comes from Copper and Fitting?

Plumbing


What has the author Leslie Avinal Miller written?

Leslie Avinal Miller has written: 'Plumbing and pipe-fitting layout job sheets' -- subject(s): Pipe fitting, Plumbing


Are tubs included in plumbing rough in?

No. Plumbing rough in refers to the installation of pipes and fitting to the fixtures, not the installation of the fixtures themselves. That is called plumbing trim.


Difference between coupling and pipe union?

A coupling is a threaded or soldered solid fitting, a union is a fitting that joins two pipes and can be taken apart with wrenches.


What is plumbing tee?

it is a T shaped pipe fitting that joins 3 pipes


How is a fitting replaced on a copper line for a refrigerator?

Depends on how it is connected flare, compression or brazed or soldered or screwed IPS or FIPS