0
Would control board keep reversing valve from working on a heatpump?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Bad effects of Sugar in car engine?
When sugar is placed in a car engine, it can clog up the engine. This may leave it not working properly and would have to be flushed or replaced.
How boiler feed valve works?
There are automatic boiler feeder and manual feeds and depending on the desired working pressure required that would determine the "SET" pressure of the feeder
What is the working pressure for NPT thread's?
1/4" thru 1/2" can be rated as high as 15,000 psi 3/4" thru 1" can be rated as high as 10,000 psi Anything larger would only be rated no higher then 5000 psi. ..... But the type of material/wall thickness will directly effect the working pressure ratings
What would the head pressure do if the fan motor on an air-cooled condenser stopped working?
The head pressure and compressor current would normally rise (strong winds and/or rain and/or very low air temperatures will reduce this effect). Less heat would be removed from the refrigerant and therefore deliver less cooling.
How does an electromechanical relay work?
All electrical relays consist of two circuits. 1.. A control circuit that utilizes a control voltage with a minimum current to switch a 2.. Power circuit requiring much greater current. The advantage of using this type of circuitry is that the switches or sensors that control large loads can be very small, {i.e. pilot switches, limit switches, sensors, etc.}, since they are the control switching device that can be capable of switching loads up to 600 amperes. This arrangement allows a very small wire size for controlling large loads. Without the use of relays, switches that control larger loads would be very expensive and occupy much more space.
Who is at fault when car reversing into space hits a car in road?
The reversing car attempting to park would be at fault. The car already traveling in the road would have the right of way since they are already properly in motion and traveling in the correct direction of traffic.. The reversing car would be traveling against the flow of traffic and has an obligation to ensure that the way is clear before reversing.
What would cause the cruise control on a 1998 Ford Explorer to stop working?
my control cable frayed....
What would cause cruise control to stop working on a 1989 chevy truck?
the cruise control is broken....
What are disadvantages of reversing entries?
Some of the disadvantages of reversing entries would be that an error can either overstate or understate the account, reversing entries also doubles the work for accountants and it also increases the chances for errors.
When using heat why would ice up on your central heating unit?
Assuming you are talking about a heatpump... Defective defrost timer board or thermostat.
Why would the Heater AC control switch stop working?
Could be low on freon,
Why would the cruise control suddenly quit working in a ford five hundred?
Blown fuse would be where to look first.
Would you use reversing entries on merchandise inventories?
why is merchandise inventory reversed
How do you disable the reversing valve on a heat pump so you can run with a straight cool air handler?
Depending on the brand of air conditioner, it is either the removal of the signal voltage to the valve, or the constant application of signal voltage to the valve. Most brands on the market are powering the reversing valve in the cooling mode. This would be easiest as you would have to make no changes if you wish, and only switch your thermostat to Emergency heat instead of heat, effectively not using the heat pump. On Rheems and Ruuds for example, the unit is in cooling mode unless the reversing valve has voltage applied to it. If you have a Rheem or Ruud, no change would be necessary except to change your thermostat to a correctly wired standard version rather than a heat pump specific version. Many electronic thermostats have this built in. Like above, you could also simply use Emergency heat instead of normal Heat switch at the thermostat. Either way, heatpump wiring can be tricky for even a good service tech if they aren't accustomed to working with heat pumps. So its best to have this done by a service company that works with heat pumps a bit.
What would make cruise control stop working on a 1990 Chevy silverado?
BROKEN CRUISE CONTROL CABLE (CHECK AT THROTTLEBODY AND FOLLOW TO TRANSMISSION)
What would keep the cruise control from working on a 2002 Mitsubishi Galant es?
one possibility would be a loose or disconnected vaccume line. trace the line comming from the speed control actuator.
What is the minimum distance for reversing a car from a garage?
till it clears the door i would guess
