0
Would it matter if droplets of distilled water were left in the burette when it was filled with sodium hydroxide?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why is it necessary to rinse the burette with sodium hydroxide before you completely fill it up?
Before a burette is used, it needs to be cleaned. During the cleaning process, usually, water is introduced into the burette. Be the water clean or not, if the burette is then used without rinsing it with the solution that it is going to be filled with, the result of that analytical exercise will not be precise and accurate. The reason is that water residue in the burette would dillute the solution when it's filled in the burette which would make it impossible to determine the exact concentration of the solution moved by the burette. By rinsing and re-rinsing the burette several times with the solution it is going to be filled with, residue water from the cleaning process would be successfully removed from the burette as are other leftover substances from the cleaning process. This practice is quite important as basic analytical technique.
What are the function of base burette in laboratory?
Base burettes are used for base titrants. Basically this is used in titrations where the analyte is an acid.
Why it is preferred to take acid in burette during acid base titration?
The burette can be filled with either acid or base. The acid will go into the burette only if you want to titrate a base , i.e. you don't know the concentration of the base and want to find out. The solution of known concentration goes always into the burette (in order to be able to measure the volume taken to complete the reaction) and so if you wanted to find out the concentration of an acid you would put the base into the burette.
What is the use of acid and base burette?
The general use of acid/base burettes I am familiar with is to determine the concentration of either the acid or base from the known concentration of the other solution. The two burettes are set side by side, and a quantity of acid is placed into a Erlenmyer flask from the acid filled burette and then the solution from the base filled burette is run into the flask along with indicator to the point of color change. By the amount titrated one can use a simple equality to find the concentration of the unknown solution.
Function of a burette?
A burette, or buret, is a uniform-bore glass tube with fine gradations and a stopcock at the bottom, used especially in laboratory procedures for accurate fluid dispensing and measurement. The buret is commonly used in titrations to measure precisely how much liquid is used.
Would it matter if droplets of distilled water were left in the buret when it was filled with sodium?
Yes, as it will serve to dilute the concentration of the sodium hydroxide being placed in the buret. You will being adding a known concentration of sodium hydroxide and ending up with an unknown concentration.
Would it matter if droplets of distilled water were left in the buret when it was filled with sodium hydroxide?
Yes, as it will serve to dilute the concentration of the sodium hydroxide being placed in the buret. You will being adding a known concentration of sodium hydroxide and ending up with an unknown concentration.
Why is it necessary to rinse the burette with sodium hydroxide before you completely fill it up?
Before a burette is used, it needs to be cleaned. During the cleaning process, usually, water is introduced into the burette. Be the water clean or not, if the burette is then used without rinsing it with the solution that it is going to be filled with, the result of that analytical exercise will not be precise and accurate. The reason is that water residue in the burette would dillute the solution when it's filled in the burette which would make it impossible to determine the exact concentration of the solution moved by the burette. By rinsing and re-rinsing the burette several times with the solution it is going to be filled with, residue water from the cleaning process would be successfully removed from the burette as are other leftover substances from the cleaning process. This practice is quite important as basic analytical technique.
What are the function of base burette in laboratory?
Base burettes are used for base titrants. Basically this is used in titrations where the analyte is an acid.
How would your results have differed if the tip of the burette was not filled with sodium hydroxide before the initial volume reading was recorded?
You would be lead to assume that there was more NaOH in the pipet than there actually was. Since when for example the pipet reads 10ml this is talking when the space in the burette is also filled up. When it is that the reaction takes place between the NaOH and acetic acid you would think that you used more NaOH than you really did, which will ultimately make you think more acetic acid was in the vinegar than was in fact.
What are air masses of tiny water droplets or ice crystals?
Clouds are air masses filled with tiny water droplets or ice crystals.
Why it is preferred to take acid in burette during acid base titration?
The burette can be filled with either acid or base. The acid will go into the burette only if you want to titrate a base , i.e. you don't know the concentration of the base and want to find out. The solution of known concentration goes always into the burette (in order to be able to measure the volume taken to complete the reaction) and so if you wanted to find out the concentration of an acid you would put the base into the burette.
What is the use of acid and base burette?
The general use of acid/base burettes I am familiar with is to determine the concentration of either the acid or base from the known concentration of the other solution. The two burettes are set side by side, and a quantity of acid is placed into a Erlenmyer flask from the acid filled burette and then the solution from the base filled burette is run into the flask along with indicator to the point of color change. By the amount titrated one can use a simple equality to find the concentration of the unknown solution.
Function of a burette?
A burette, or buret, is a uniform-bore glass tube with fine gradations and a stopcock at the bottom, used especially in laboratory procedures for accurate fluid dispensing and measurement. The buret is commonly used in titrations to measure precisely how much liquid is used.
What is the proper way to read a burette?
Any fluid!!! It is like a pipette, however, it is usually more accurate because you can use a burette loader which allows fine tuning of the liquid but not as fine as a gilson pipette. Basically, it is just a piece of apparatus used measuring liquids.
What happens if the tip of the burette is not filled before the titration begins?
The measure of volume used in the titration will be inaccurate, because there will appear to be more titrate used than has actually been dispensed.
What happens in water droplets to cause rainbows?
The thing that happens in water droplets to cause rainbows is the light shines through it. rainbow9897654321: it is a prism that make it white is made of all color it reflects for the droplet when i goes through the glass its a rain bow that is filled with water its a experiment but you got to put it in the sun with a glass filled with water
