0
You just installed a 1996 5.7 liter gm engine in your 1984 four winns boat and you are trying to set the timing and you are looking for proper settings?
check out an engine and distributor shop they will get the timing set for you, if you are looking for the firing order i have long since forgotten. once the distributor is set right it is a matter of twisting the cap till your engine runs nice, however you dont want to do this unless you are comfortable with engines
What else can I help you with?
Does the thermostat have to be in the Plymouth Voyager?
Yes, the thermostat needs to be installed for proper engine operation.
What is Crank torque settings on c190 desil?
The crank torque settings for a C190 diesel engine typically range from 100 to 120 Nm (Newton-meters), depending on the specific engine model and manufacturer guidelines. It's crucial to consult the engine's service manual for the exact specifications and any recommended tightening sequences to ensure proper installation and prevent damage. Proper torque ensures optimal performance and durability of the engine components.
What size of battery is needed for stock 350?
Depends on what vehicle the engine is installed in. Anyplace that sells batteries cantell you whatthe proper size battery is.
Yes with the proper installation kit and harness this can be installed in most vehicles.?
Yes with the proper installation kit and harness this can be installed in most vehicles.
What is the tappet settings on a Mazda E2000 van?
The tappet (valve clearance) settings for a Mazda E2000 van typically vary depending on the engine type. For the 2.0L engine, the clearance is generally around 0.15 mm (0.006 inches) for both intake and exhaust valves when the engine is cold. It's important to consult the owner's manual or a repair guide for specific specifications and procedures, as settings may differ based on the model year and engine variant. Always ensure proper adjustments are made for optimal engine performance.
Will it hurt if piston rods go back in different than before rebuild?
Yes, if piston rods are not installed correctly during a rebuild, it could cause engine damage, poor performance, or even complete engine failure. It is crucial to follow the manufacturer's specifications and ensure proper alignment and torque settings during reassembly.
Why might a scanner not work after being installed?
Please check whether you installed proper driver for your scanner.
Should engine lift after your motor mounts are replaced?
If the old mounts were compressed over the years, there could be a small lift of the engine with new mounts. If the lift is more than an inch or so, you should check that the proper mounts were installed.
Why does the light for the airbags stay on after you just installed the 2006 ford focus airbag kit?
Disconnect the "hot" wire on your battery for about an hour, or two, and the computer should reset itself and go to the proper settings, recognizing your new equipment.
What are the tappet settings for a 2003 L200 4LIFE?
The tappet settings for a 2003 L200 4LIFE typically require a clearance of 0.15 mm (0.006 inches) for the inlet valves and 0.20 mm (0.008 inches) for the exhaust valves when the engine is cold. It's important to consult the vehicle's service manual for specific details and confirmation, as settings may vary slightly based on the engine variant or modifications. Always ensure the engine is at the correct temperature and follow proper procedures when adjusting.
What are tappet settings for td42?
The tappet settings for a Nissan TD42 engine typically involve adjusting the valve clearances to ensure proper engine performance and avoid damage. For the TD42, the recommended valve clearance is usually set at 0.30 mm (0.012 inches) for both intake and exhaust valves when the engine is cold. It's important to follow the manufacturer's specifications and procedures when performing this adjustment. Always consult the service manual for the specific model year for precise settings and procedures.
What is the cylinderhead bolt settings on a mitsubishi 4g15 engine?
The cylinder head bolt settings for a Mitsubishi 4G15 engine typically involve tightening the bolts in a specific sequence to a set torque specification. It's important to follow the manufacturer's recommended procedure to ensure proper sealing and prevent any damage to the engine components. It's advised to consult the specific service manual for your engine to get the accurate torque specifications and tightening sequence.
