0
Sprinkler system design is an area that can become very complex very quickly. A large system requires a person to perform complex mathematical calculations while also accounting for the water needs of different plants and the layout of the property. Some professionals specialize exclusively in sprinkler system design for this reason. Homeowners can take several steps to help plan a workable and functional design for a lawn or yard.
Every sprinkler system design should start with a detailed and accurate map of the property. It should include the house, fences and major plantings like trees or raised beds. The map should also include noticeable changes in elevation throughout the property. The next step is to use a template, compass or other guide to start plotting where each sprinkler head will be located. Overlap between the heads should be minimal. Similarly, the range of each sprinkler head should not extend beyond the property by a large amount. It is important to avoid placing sprinklers too close to the house where they can cause water and foundation damage.
The next step will determine what components are necessary as part of the sprinkler system design. The two primary numbers that must be measured from an outdoor water source are pounds per square inch (PSI) of pressure and the gallons per minute (GPM). There are several small and inexpensive devices to measure PSI and GPM. Some municipal water services will also run a test and provide the information. GPM is used to determine the flow rate of the sprinkler system and the potential number of heads that can be used. The PSI determines how far the water will travel as well as the types of heads that can be used. Homes with well systems or homes on large properties will likely need a water pump to boost the PSI so that water can work through all the pipes and up inclines.
The next step should be to start designing small circuit blocks of Plumbing. This means plotting how valves, sprinklers, pipes and other fittings will fit together in just a small area. Planning several of these in sequence will make the sprinkler system design more manageable. One of the final steps should be to consult with a professional for advice before installing the system. Any number of minor issues could cause the system to fail. Professionals will see any problems quickly and can suggest fixes. Additionally, professionals will have knowledge of any local building codes or regulations that the system must meet.
What else can I help you with?
Will you get a discount on homeowners insurance if you install a sprinkler system?
=== === If its a yard sprinkler, no. If its a fire sprinkler, yes.
Does homeowners insurance cover sprinkler system?
Your homeowners insurance should cover damage to your sprinkler system if the cause of the damage is covered by your homeowners insurance policy such as fire, lightning, freezing of pipes, etc. Homeowners insurance is not a maintenance policy and will not cover mechanical failure of your system.
What is a sprinkler system for a house?
A sprinkler system is a device that waters your plants or grass
What is the purpose of a sprinkler head plug and how is it used in a sprinkler system?
A sprinkler head plug is used to block off a sprinkler head in a sprinkler system. It is typically used when a sprinkler head needs to be temporarily removed or replaced. The plug prevents water from flowing out of the system through the open hole where the sprinkler head would normally be.
How often should you replace freon in home sprinkler system?
There is no freon in a home sprinkler system.
What is the function of the sprinkler system control valve?
The function of the sprinkler system control valve is to regulate the flow of water to the sprinkler system, allowing for the system to be turned on and off as needed to water the designated area.
What is the purpose of a sprinkler system blowout adapter and how is it used to winterize a sprinkler system?
A sprinkler system blowout adapter is used to remove water from a sprinkler system to prevent freezing during winter. It is connected to an air compressor to blow out any remaining water in the system, ensuring that no water is left to freeze and potentially damage the pipes or sprinkler heads.
How does a sprinkler valve work to control the flow of water in a sprinkler system?
A sprinkler valve works by opening and closing to control the flow of water in a sprinkler system. When the valve is open, water is allowed to flow through the system and reach the sprinkler heads, which then spray water onto the desired area. When the valve is closed, water flow is stopped, preventing water from reaching the sprinkler heads. This allows for precise control over when and where water is distributed in the sprinkler system.
What is the purpose of the sprinkler system cap and how does it contribute to the overall functionality of the system?
The purpose of the sprinkler system cap is to cover and protect the sprinkler head from damage and debris. It helps maintain the integrity of the system by ensuring that the sprinkler head remains functional and can effectively distribute water in case of a fire emergency.
Where is the sprinkler irrigation system found?
Sprinkler irrigation is mostly found in farms.
What is the function of a control valve in a sprinkler system?
A control valve in a sprinkler system regulates the flow of water to the sprinkler heads, allowing for precise control over the distribution of water and ensuring efficient operation of the system.
Does homeowners insurance cover parts of underground sprinkler system damaged due to tree uprooting from hurricane?
My initial thought on this is that the sprinkler line would be covered as it is attached to house and was damaged by a tree being blown over by wind. That is unless you happen to have an insurance policy that excludes wind damage which is not uncommon in hurricane prone areas.
