0
Chevy venture 2000 power windows not working tried the fuse box circute breaker for the wndows need some ideas where to go from here?
Hi,
You will need to do a little troubleshooting with a test light or multimeter. If you have power to the main switches, then you will have to check the switches and the wiring for problems.
I have included a link that gives the details of the power windows in this van.
Good Luck, Greg
What else can I help you with?
Does Jeep have fuse for 03 Jeep Cherokee windows?
The windows are fed by a circuit breaker. If all are not working you should check the harness to the driver's door for broken wires.
Where is the fuse for the power windows located on a 1995 Isuzu Rodeo because all four automatic windows quit working at the same time?
That circuit has a relay/circuit breaker not a fuse. Chances are you have a window motor with a dead short which is not allowing breaker to reset. Check the drivers side first; unplug it the window motor and see if the other windows come alive.
Why won't both Power Windows go down Would there be a fuse to check?
There is a resetting circuit breaker instead of a fuse on most models. On my 1995 there are two such reset breakers in my fuse panel and they are interchangable. You need to check to see if there is power going to the breaker. If there is no power on the other side then the breaker has likely failed open. You can jumper across the terminals and if the windows start working then you know the breaker is bad. Had a similar problem, turned out that the clips where the CB plugs in under the dash where not making a good connection with the breaker, just use a flat head and pry them closer.
What are the safety precautions to consider when working with a circuit breaker?
When working with a circuit breaker, it is important to follow safety precautions such as wearing insulated gloves, ensuring the power is turned off before working on the breaker, and using proper tools to avoid electrical shocks.
Electricity generation using speed breaker working?
how to work a project on speed breaker energy
What would cause all four power windows to stop working at the same time on a 1997 Chevrolet Malibu?
Power windows are protected by a circuit breaker. So you would have to have a bad relay ,the master switch is defective or you have a broken wire where the door opens.
Is it dangerous to have water in circuit breaker?
Yes. Water can damage the breaker and prevent it from working, or it may continue to carry current after the breaker trips.
Why won't the auto windows work all of a sudden the fuse is okay?
If all the window switches are not working, I would suspect a common thread like a circuit breaker or the power window relay is bad.
What is the working area of the Windows XP screen?
what is the working area of the windows xp screen
What do you do if one of the breakers in the breaker box isn't working?
If a breaker in the breaker box isn't working, first ensure that the breaker is fully in the "on" position. If it trips again immediately or doesn't stay on, turn it off and check for any overloaded circuits or damaged wiring connected to that breaker. If the issue persists, consider replacing the breaker or consulting a licensed electrician for a thorough inspection and repair to ensure safety. Always prioritize safety and avoid working on electrical systems unless you are qualified to do so.
How do I properly install a GFCI breaker in my electrical system?
To properly install a GFCI breaker in your electrical system, first turn off the power to the circuit you will be working on. Remove the panel cover and locate the circuit breaker you will be replacing with the GFCI breaker. Disconnect the wires from the old breaker and connect them to the new GFCI breaker according to the manufacturer's instructions. Secure the GFCI breaker in place and replace the panel cover. Turn the power back on and test the GFCI breaker to ensure it is working properly.
How do I install an AFCI breaker?
To install an AFCI breaker, first turn off the power to the circuit you are working on. Remove the panel cover and locate the breaker slot. Insert the AFCI breaker into the slot and connect the hot wire to the breaker terminal. Connect the neutral wire to the neutral bus bar and the ground wire to the ground bus bar. Secure the breaker in place and replace the panel cover. Turn the power back on and test the AFCI breaker to ensure it is working properly.
