0
Depending on engine model, remove oil filler cap and remove top plastic cover over engine...locate thermostat housing that usually is attached to first hose going to radiator. You will see a screw and fitting in the top of housing. this is the bleeder screw for cooling system. with engine idling, use a screw driver and just crack open the bleeder enough to let out the air, in a few seconds coolant will start to run out of bleeder, retighten screw and reassemble cover...CAUTION: these bleeders will not take much abuse so if its not movin with first attempt do not force it. Check your direction of turn make sure your going the right way.
What else can I help you with?
How do you bleed air out of the cooling system of a 2000 Oldsmobile intrigue 3.5 liter engine?
To bleed air out of the cooling system of a 2000 Oldsmobile Intrigue with a 3.5-liter engine, start by ensuring the engine is cool and remove the radiator cap. Then, with the heater set to the maximum setting, start the engine and allow it to reach operating temperature. As the thermostat opens, check for air bubbles in the coolant; add coolant as needed to maintain the level. Once you see a steady stream of coolant without bubbles, replace the radiator cap and ensure the system is sealed.
How do you bleed the coolant system for 2002 Oldsmobile alero?
To bleed the coolant system on a 2002 Oldsmobile Alero, start by ensuring the engine is cool and the coolant reservoir is filled to the appropriate level. Locate the bleed valve on the engine or heater core, if applicable; otherwise, you can use the radiator cap. Start the engine and allow it to reach operating temperature, then carefully open the bleed valve (if present) or the radiator cap to release trapped air. Once you see a steady stream of coolant without bubbles, close the valve or cap, and check the coolant level again, adding more if necessary.
How do you bleed air out of coolant system 97 Saturn?
procedure on how to bleed air out of coolant system on 97 saturn ls
How do you bleed your V6 coolant system?
how do i bleed my accord v6 2000 coolant system, its has air and the rev's gone up & down......
Where is the place you bleed coolant system?
It is not necessary to bleed the coolant system. If you mean "drain" the system, there is usually a plastic plug on the radiator or, you can pull the lower radiator hose off.
How Do you Bleed The Coolant System On A 1998 Beetle?
To bleed the coolant system on a 1998 VW Beetle, remove the top from the overflow tank. Run the car for 10 to 15 minutes to force any air out of the system, then check the coolant level. Add coolant as needed.
How do you bleed the coolant system on a 2002 impala?
There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.
How do you bleed air out of the cooling system of a 2001 Oldsmobile Intrigue 3.5 liter engine?
The 2001 General Motors (Oldsmobile Division) Intrigue came equipped with the 3.5L engine and 4-speed automatic transmission FWD. One method of purging air from the cooling system after repairs and flushing it involves refilling it, and running the motor and heater, and leaving the radiator pressure cap off to 'burp' off the air trapped inside.
How do you Bleed the coolant system on a 2002 Chevrolet Impala?
There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.
How Do you Bleed The Coolant System On A 1998 2.0 Beetle?
Start by taking the top off of the coolant overflow reservoir. To bleed the system, run the 1998 VW 2.0 Beetle about 10 minutes, then check the coolant level. Add coolant if needed, then replace the reservoir top.
How do you bleed coolant system after replacing thermostat?
what is the year make & modle of it??
How do you bleed the coolant system on a 1999 mercury villager?
Not necessary on this vehicle.
