0
You will have to take the transmission out, then pull the torque converter out of the trans. and you will see a shaft sticking out of the front of the trans. and a seal that is in the trans around the shaft. Pop that seal out and put the new seal in it's place.
Then slide the converter back over the shaft and start pushing it back into the trans being sure to turn it clockwise while pushing it back in place you should fill the converter click 3 times, and when it is all the way in you will not be able to slide your fingers between the converter and transmission bell housing around the top are the sides of the converter, If you can then the converter is not in correctly pull it back out and start over until it is all the way in. Just be sure that you are turning the converter while you are pushing it in the transmission. Then put the trans. back in the truck.
What else can I help you with?
How do you change the front seal on a c-6 transmission?
remove the trans. and get a seal puller
If you overfill a 1976 350 turbo trans will it leak out the rear of the trans by the front U joint Its not leaking out of the seal?
The yoke on the driveshaft of a gm turbo 350 trans has a small vent hole in it. If the trans is over filled to the point fluid comes out of it you will do serious damage to the trans if you try to drive the vehicle.
How do you change rear main seal 6.0 turbo diesel?
pull trans. fly wheel one piece rear main seal not a job for a shade tree
Where is the front seal located in the turbo 350 transmission?
It is located at the front of the transmission, on the pump. You can see it on the pump were the torq converter goes into the transmission. The trans has to be pulled out of the car to do the repair.
What is the easiest way to change transmission seals in a 76 Chevy 350?
what seals are u trying to change if it is the front seal behind the torque converter you have to pull the trans and the TQ if its the front pump seal you must pull trans, tq and front pump to replace out put shaft seal you have to pull the driveline buy a repair manual that will help and ask for some help maybe some one with some auto trans experience good luck i want too change the seal on the shifter side of a 350 Chevy trans
Can you change a turbo seal in a cummins isx turbo?
How to remove turbo on 200 cummins ISX
How do you change the front seal on an automatic transmission in a 1996 dodge Dakota?
you have to remove trans.after trans is removed remove tork.conv.check bushing in front pump you will find that it is bad
How do you change torque converter seal on 1998 Plymouth breeze?
You have to pull drive shaft and take off trans- the front pump seal is on the front of the trans behind the converter. It looks just like the one at the end of your tail shaft. Except for the labor, replacing seal itself is easy once you get to it. If you are mechanically inclined and have the tools, you can do it yourself.
What is the seal called where the front drive shaft goes into the front axle?
I believe it's called a trans-axle output shaft seal. Could also be the front differential pinion seal.
How do you change a front seal on a turbo 350 transmission?
You will have to take the transmission out, then pull the torque converter out of the trans. and you will see a shaft sticking out of the front of the trans. and a seal that is in the trans around the shaft. Pop that seal out and put the new seal in it's place. Then slide the converter back over the shaft and start pushing it back into the trans being sure to turn it clockwise while pushing it back in place you should fill the converter click 3 times, and when it is all the way in you will not be able to slide your fingers between the converter and transmission bell housing around the top are the sides of the converter, If you can then the converter is not in correctly pull it back out and start over until it is all the way in. Just be sure that you are turning the converter while you are pushing it in the transmission. Then put the trans. back in the truck.
How do you take a front transmission seal out of a 1992 Chevy Blazer?
You will have to remove the transmission and pull the toqure converter out of the front of the trans. then you will see a seal in the center of the trans. Remove it with a screw driver, then clean and install new seal it will drive in with a hammer if your good. You may need a seal driver.
How do you change front seal on transmission on 1997 Chevy s10 4x4 blazer?
you have to un bolt engine at the bell housing where the engine and trans meet and and un hook wires from trans loosen or remove mounts un hook drive shaft and slide trans back be careful and check if any vacuum lines to to the trans too if vac lines go to trans u have to un hook them as well take torque converter off and then u can get to the front seal u pop the front seal off and pop a new one in then hook every thing back up and it is done
