answersLogoWhite

0

To change the lower ball joint on a Mercury Sable, start by safely lifting the vehicle and removing the front wheel. Next, detach the brake caliper and rotor, then remove the lower control arm from the steering knuckle. Use a ball joint separator to disconnect the old ball joint from the control arm, and then press in the new ball joint using a suitable tool. Finally, reassemble everything in reverse order, ensuring all bolts are torqued to manufacturer specifications.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

Show how to change the thermostat in a 2000 Mercury Sable?

mercury sable


How do you change out a power steering switch on a 2001 mercury sable with a 3.0 engine?

how do i change out a power steering switch on a 2001 mercury sable with a 3.0 engine?


How much does it cost to fix a ball joint?

how much would it cost on a 2004 mercury sable


Where is the crank sensor on a 2004 Mercury Sable?

lower right front of the engine


When change your 1989 Mercury Sable timing belt?

In a 1989 Mercury Sable : Both the 3.0 and the 3.8 litre V6 engines have a timing CHAIN


When was Mercury Sable created?

Mercury Sable was created in 1986.


Where is the air compressor located on a 1999 Mercury Sable?

Right side lower belt driven accessoriy


Where is the transmission oil cooler located on a 2008 mercury sable?

Front lower left side of the radiator


Mercury sable air bag removal?

how do I remove my air bag from my mercury sable


2002 Mercury Sable paint code?

what its the paint code for 2002 mercury sable


How do you Troubleshooting starter or solenoid 2004 Mercury Sable?

where is the solenoid on a 2004 mercury sable


How do you repalce a lower ball joint 0n 02 sable?

To replace a lower ball joint on a 2002 Sable, you will need to jack up the vehicle, remove the wheel, loosen the ball joint nut, separate the ball joint from the control arm, and then press out the old ball joint with a ball joint press. Install the new ball joint by pressing it in and then reassemble everything back together. Make sure to tighten all nuts and bolts to the manufacturer's specifications.

Trending Questions
When was the first Model T car built? 1997 Pontiac transport Why wont your fuel pump work New fuel pump relay and power to the pump but it still does not work? Will a 2008 Ford Ranger bed fit on a 2003 Ford Ranger? Where is the starter on a 1995 Oldsmobile Aurora located? How good is the Chrysler Crossfire? How much horsepower does a pw 50 have? Where can you find a wiring diagram for an 1987 Yamaha Warrior? Where is the crankshaft position sensor located on a 1989 jeep wrangler? Would a stock 2003 mercury marauder beat a stock 1996 impala SS? What dtc means on cars trouble codes? Hood won't open on a 1996 Pontiac Grand AM When lever is pulled from inside there is tension but hood won't open or even pop up to pull the lever It is negative nineteen degrees here also HELP? How do i disarm a factory alarm system on a 1994 Jeep Grand Cherokee? Will the 360 out of the durango bolt to the t150 transmission in your cj5? Where do you find the paint codes on a 1987 cutlass supreme? Did Spencer on i Carly really save the singer the plain white t's? The heater in your 1995 Jeep Grand Cherokee Laredo has quit heating even though the water temperature appears normal on the gauge Any ideas? How do you change the in line fuel filter on a 1997 Ford Expedition Eddie Bauer with a 5.4 Triton Motor? How do you find a cylinder that's missing on a ford f-150 1997? Does a2006 f250 have locking 4x4 hubs? 1994 Plymouth voyager 6-cylinder was idling rough for 4 months and mechanic said it was just a dirty injector but now it stalled after making a turn and wont start?