0
What else can I help you with?
How do you replace the gear shift cable on a Ford Taurus - Mercury Sable?
There are 2 excellent write-ups on the procedures for replacing the shifter cable, one for floor shift and column shift each, at the Taurus Car Club site. See Related links below for more information.
How many bolts in 2000 Mercury Sable starter?
The 2000 Mercury Sable starter will have three retaining bolts. There will be two cable retaining nuts on the front of the starter.
How do you get a hood open after the hood latch cable broke on a Ford Taurus - Mercury Sable?
AnswerI assume the handle broke off in the car. You will have to by a new cable/handle assembly ($30.00) so I would: Cut the remaining handle and end off the cable housing so you can get at the inner cable core. Then take a vise grip and pull on the inner core to release hood latch. New housing/cable assemblies are available at your Ford dealer. get in your floorboard and dismount your dash piece so you can see up under there... this will help you determine where your hood release cable brokeAnswerMy 97 Ford Taurus hood doesn't pop open on its own - however if you pull the pop hood thing and then take a key or screwdriver and slide it under the hood and push up you can pull it up with your hand. This has scratched my hood up but at least I can get it open.
How do you replace the Hood Cable in a 1998 Mercury Sable?
To replace the hood cable in a 1998 Mercury Sable, start by opening the hood and disconnecting the battery for safety. Remove the inner fender liner or any necessary panels to access the cable's routing. Detach the old cable from the latch mechanism and pull it out through the firewall. Install the new cable by threading it through the same path, securing it to the latch mechanism, and reassembling any panels or components you removed.
Where is the starter relay located on a 1995 Mercury Sable?
Look on inner fender--Follow + battery cable should connect to solenoid
How do you put cable from battery through firewall in 1999 mercury sable?
Drill a hole and then insulate the hole with a rubber washer so the cable doesn't chafe on the jagged hole.
How do you remove the floor center console CD player in Ford 2003 Taurus - Mercury Sable?
To remove the floor center console CD player in a 2003 Ford Taurus or Mercury Sable, first, disconnect the negative battery cable to ensure safety. Next, carefully pry off the trim panel surrounding the console using a trim removal tool. Remove any screws securing the CD player, then gently slide the unit out of the console. Finally, disconnect the wiring harness and any additional connectors before fully removing the CD player.
Why does my gas pedal not work on a Mercury Sable - Ford Taurus?
If the gas pedal just falls to the floor, that would indicate:the cable connecting it to the throttle has brokencome disconnected from the throttlethe throttle body linkage has brokenThe spring on the throttle linkage has broken (this is one you should be hoping for!)If the cable is still properly connected, the problem then is going to be inside the throttle itself.
How to repair a speedometer cable on a 1990 Mercury Sable?
It would probably be cheaper to replace the cable, check with your local auto wrecker. This used part should be very inexpensive, compared to repairing it.
What size wrenches do you need to change a starter on a 96 Sable - Taurus?
A 13mm wrench will do the job very nicely.Add in a good selection of socket extensions, and a 8 or 10mm socket for the wire connections.NOTE: Disconnect the negative battery cable FIRST!See "Related Questions" below for much much more detail on replacing a Taurus/Sable starter
What is the procedure for replacing a broken hood latch cable on a 91' mercury sable?
first you need to open up the hood, take it into a body shop. they encounter this problem frequently in accidents and such. and then just replace the cable
How to reset Service Engine Soon cancel code in 1997 Mercury Sable after service for that code?
Disconnect the positive battery cable and wait 30 seconds or so then reconnect the cable. If this does not clear it you have other problems.
