0
What else can I help you with?
How do you change a Ford F-150 transsmission?
Its a pain. You first have to drop the torsion bars under the truck. Then get a pulley puller and push the torsion bars back up to remove the metal pieces holding the torsion bars in. Remove the puller and take the torsion bars off. You will then need to remove the bracket holding the torsion bars. ONce that is done, you will have enough clearance to drop the tranny. The hard part is getting the torsion bars back on. Come to think of it, I think you can buy a tool from Ford to pull the torsion bars off. It pretty expensive that why I use a pully puller. Not all F-150s have torsion bars. Buy a Chilton Repair Manual for your correct year. It'll tell you everything step by step.
Do you have to take off the torsion bars when you replace your clutch in a 4x4?
Yes, in many 4x4 vehicles, you often need to remove the torsion bars to access the transmission for a clutch replacement. This is especially true for models where the torsion bars are mounted in a way that obstructs the transmission removal. Always consult your vehicle's service manual for specific instructions and procedures related to your model.
How do you raise the front end of your 85 Nissan 720 pickup using the torsion bars?
You need to crank them up.
Do your tires let you know when they need replacing?
In the tread there are small 'bars' at the bottom surface about 2-3 mm high, when average tread wear is down to these 'bars' you should get new tires.
When replacing the front sway bars in a 2002 Trailblazer does the battery need to be disconnected?
no it does not.
How do you install new torsion bars that keep the trunk lid up on a 2001 Honda Accord?
first you will need to have a crown vick in order to do this,
On a 98 Ford 150 4x4 do you have to remove the torsion bars to remove the transmission and transfer case?
Yes you do have to remove the bars or at least the torsion bar cross member and to do that you either need the otc tool or use a two jaw puller make sure to measure the bolt height before you start and set it the same they control your ride height
What is the biggest tire that you can fit on a 2005 Chevy silverado 1500?
If it 4x4 you need to crank the torsion bars so no rubbing happens but you can easily put 285/70R17
What is the easiest way to properly raise the rear end of a 1969 Volkswagen Bug so that the clearance is sufficient enough to pull into a driveway.?
You really need the Bentley Manual as this could be really DANGEROUS. The only way to raise or lower it is to take apart the suspension. The spring plates that connect to the Torsion bars are under several hundred pounds of pressure. They have "torsion bars" that you can rotate to raise or lower it. The "torsion bars" have splined ends, one end is fine (eg40) and the other is coarse (eg20). You rotate the bars one way and the cover the other way to raise it a lot or a little. Do a search on the internet as there are places that walk you through it also. Be aware as you may have to have the rear end realigned.
How and were is the torsion bar to adjustments on 2001 dodge sport 4x4?
On a 2001 Dodge Dakota Sport 4x4, the torsion bar adjustment is located on the front suspension system. You will find the adjustment bolts on the torsion bar crossmember, which is situated beneath the vehicle, near the front of the frame. To adjust the torsion bars, you'll need to use a socket wrench to turn the bolts, which will raise or lower the front suspension height. Always ensure the vehicle is securely supported before making any adjustments.
Replacing taillite on 2005 chevorlot silveraldo?
What about it? What do you need to know?
After replacing the starter on 1995 Saturn it still wont start?
We need more info. Need to know the symptoms. Need to know what it does and does not do.
