KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan featureThe anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time. Locks and Security 150
You will need a scan tool to program this Keyless Fob.
You can program a 2001 Chevrolet Camaro by locking then unlocking the door locks.
You can program the keyless entry remote, for your 2001 Saturn L200, by holding the unlock and lock weapons at the same time. The red light will flash on and off. The remote will be programmed when the red light stays illuminated.
see also 2004 silverado
I found an Internet site which says how to program the keyless entry remote. But there is an error: this procedure is good for Elantra 2001 to 2003. Elantra 2004 must be programmed by the dealer. http://car.justanswer.com/hyundai/n1kw-program-remote-entry-hyundai-2004
A keyless entry remote on a 2001 Toyota Sequoia can not be reprogrammed at home. The key must be taken to a dealership where the engineers can program it with new settings.
It requires the dealers scan tool.
The dealers scan tool is required.
If you have a owner's manual the directions might be in there. For my 2001 Escape that's where I found the answer
If you're asking about adding a NEW keyless remote, only a dealer can do that. It's a very specialized piece of equipment that can add the new remote to your vehicle's computer. If you're asking about RE-programming your keyless remote after replacing the battery, check the inside cover of the remote. It should give instructions on how to solve your problem.
See FOB PROG (Remote Keyless Entry Transmitter Programming) on page 2-27 of your "Owner's Manual", under Section 2: Features and Controls - Vehicle Customization Settings.....
Try this: Turn the ignition to RUN (do not start), press the unlock button on the keyless remote, ignition OFF. Repeat 2x. Turn the ignition to RUN, press the unlock button on the keyless remote twice, the power locks should cycle to indicate successful programming. Turn the ignition OFF and test remote.