answersLogoWhite

0

When you remove the interior door panel (the only tricky part is the two screws in the bottom of the door pull hand hole; they have a little plastic cap covering them so you don't see them unless you know they are there) you will see several 10mm bolts holding the metal inside liner to the frame. With the window full up, you can put a wedge in the chanel and remove the two clamps that connect the cable to the window. After removing these clamps you can remove the bolts holding the metal liner to the frame and remove the metal liner with the regulator and motor attached to it. The regulator (cable) is held on place with bolts at the top and bottom of each arm and must be replaced as an assembly. The motor and gearbox can be reused and you will see the 3 torx bolts that hold them to the left arm. Not a difficult job 2hours start to finish but the cable assembly cost about 175.00. Good luck!!

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you fix the drivers side front window that is off the track on a 2002 Lincoln LS?

The window is not off track. The window regulator is broken. In most cases you will have to replace the window motor and regulator as an assembly.


How do you remove 91 Nissan maxiam front right window regulator?

1 open door 2 remove inner panel 3 lower window 4 take out window 5 remove (4) screws from regulator 6 take regulator of rails


How do you replace 3000 gt door window regulator?

First, lower window approximately half way. This allows you access to the bolts that attach window to the regulator. Remove door panel. Using a 10mm wrench, remove the two bolts that hold window to the regulator. Then there are two upper and two lower bolts holding the regulator to the door. Then you remove the three bolts for the window motor which is toward the front of the door. You have to also disconnect the plug for the windo motor to remove the entire window regulator and motr that are all one unit. Replace the unit in the reverse way.


Can you interchange the rear window regulator with the front on a ford contour?

That would be EXTREMELY unlikely that any rear window regulator would fit in the front window, same side or not.


How do you change left front window Volvo s60 2003?

To change the left front window of a 2003 Volvo S60, first, remove the door panel by unscrewing any visible screws and prying off clips. Disconnect the electrical connectors for the window switch and remove the speaker if necessary. Then, take out the old window by lowering the window regulator and carefully sliding the glass out. Finally, insert the new window into the regulator, reassemble the door panel, and reconnect everything.


How do you remove and replace a passenger side front window regulator on a 52 plate Skoda fabia?

To remove and replace the passenger side front window regulator on a 52 plate Skoda Fabia, first, disconnect the car battery and remove the door panel by unscrewing the screws and unclipping the panel carefully. Then, detach the window glass from the regulator by removing any clips or bolts holding it in place. Next, unbolt the old regulator from the door and disconnect any electrical connectors. Finally, install the new regulator by reversing the steps, ensuring everything is securely fastened before reattaching the door panel and reconnecting the battery.


Is there a difference in the rear window regulator and front regulator in a Pontiac Aztec?

No. In fact, the wires from the rear if connected to the front will fix a 250 problem!


How do you fix the cable on a 2001 jeep Cherokee Laredo front drivers window?

To fix the cable on a 2001 Jeep Cherokee Laredo front driver's window, first remove the door panel by unscrewing the necessary fasteners and gently prying it off. Once exposed, disconnect the window motor and remove the window regulator assembly. Inspect the cable for fraying or breaks, and if needed, replace it with a new cable or regulator assembly. Reassemble the door panel and test the window to ensure it functions properly.


What could be the problem if the power window on front driver side of 1998 Lincoln Town Car works occasionally I can hear a click inside door panel when button is pushed.?

The brushes inside the motor need to be replaced. Not too difficult, but when you remove the motor, be sure not to screw up the the window regulator. It has to stay intact or spend a couple more hours and $40 or so for a new regulator.


How do you replace window regulator in 2003 Buick LeSabre front driver side?

The way that replace a window regulator in a 2003 Buick LeSabre front drive side is by removing the door panel. Next, disconnect the electrical connector on the regulator and replace.


How do you remove the window regulator on a 70 Chevelle?

Remove the armrest, door handle, and window handle. You will need a special tool to get the window handle off. They're cheap and you can get them at any auto parts store. Remove the screws at the bottom of the door panel then CAREFULLY pull the retaining clips out of the door by sliding a screwdriver between the panel and door where the clips are (you'll find them at the front and back) it is VERY easy to tear the backing of the door panel when removing them, so be careful and patient. Slide the door panel up to unhook the top of it from the door. Remove the window regulator bolts and carefully slide the rollers out of the window tracks. Carefully remove the window from the top of the door. slide the window regulator out.


How do you replace the front passenger side window regulator on a 2003 Buick Le Sabre?

To replace the front passenger side window regulator on a 2003 Buick Le Sabre, first, disconnect the vehicle's battery to ensure safety. Remove the door panel by unscrewing any visible screws and carefully prying off the panel clips. Once the panel is removed, disconnect the window motor and regulator assembly, then unbolt the old regulator from the door. Install the new regulator in reverse order, reconnect everything, and test the window operation before reattaching the door panel.