0
Jack up the rear of the car so that the tires are barely touching the ground.
Place jack stands under the frame. remove jack.
Disconnect ebrake, brake lines, driveshaft, shocks, lower and upper control arms. Might take a little force to get springs out of seats.
Axle is now separate from vehicle.
What else can I help you with?
How do you remove a right rear axle from a 98 Chevy Tracker?
To remove the right rear axle from a 1998 Chevy Tracker, first, ensure the vehicle is securely raised and supported on jack stands. Remove the wheel and brake drum to access the axle. Next, disconnect the axle shaft by removing the retaining bolts at the differential and the wheel hub. Finally, gently pull the axle out of the housing, taking care not to damage any seals or bearings.
How do you replace a wheel bearing on a 2002 Tracker?
You will need to remove the tire and wheel from your 2002 Geo Tracker. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel seal and the wheel bearing. Reverse the process to install the new wheel bearing.
Disassemble rear axle of a 2001 Chevy Tracker?
Disassembly
How do you replace halfshaft 2002 Chevy Tracker?
To replace the halfshaft on a 2002 Chevy Tracker, first, lift the vehicle and secure it on jack stands. Remove the wheel, then detach the brake caliper and rotor to access the halfshaft. Use a socket to remove the axle nut, then pull the halfshaft out of the hub and transmission, ensuring you check for any retaining clips. Install the new halfshaft by reversing the disassembly steps, making sure to torque all bolts to the manufacturer's specifications.
How do you remove front cv joint on a 2002 Chevy Tracker?
To remove the front CV joint on a 2002 Chevy Tracker, start by safely lifting the vehicle and removing the front wheel. Next, detach the axle nut after removing the brake caliper and rotor. Then, use a pry bar to pop the CV joint out of the transmission or differential, taking care to support the assembly as you pull it out. Finally, reverse the process to install the new CV joint, ensuring all components are properly secured.
How do you replace left front axle shaft 1999 tracker?
To replace the left front axle shaft on a 1999 Chevy Tracker, first, raise the vehicle and secure it on jack stands. Remove the wheel, then detach the brake caliper and rotor for better access. Unscrew the axle nut and disconnect the lower ball joint, allowing you to pull the axle out of the hub. Finally, remove the old axle shaft from the transmission, install the new axle shaft, and reverse the steps to reassemble everything.
How do you change wheelbearing in a 2002 Chevy Venture?
Rear you have to change the entire hub assembly Front you have to remove the axle shaft
How do you replace cv axle on a 1995 tracker?
To replace the CV axle on a 1995 Chevy Tracker, first, securely lift and support the vehicle, then remove the wheel and brake components as necessary to access the axle. Remove the axle nut and any retaining clips, then pull the axle out of the hub. Next, detach the inner end from the transmission or differential by either pulling it out or using a pry tool if it's stuck. Finally, install the new axle by reversing the removal steps, ensuring all components are properly secured.
How do you replace a front hub assembly on a 2002 Chevy Tracker?
To replace the front hub assembly on a 2002 Chevy Tracker, first, elevate the vehicle and remove the front wheel. Then, disconnect the brake caliper and rotor, followed by removing the axle nut and any bolts securing the hub assembly. Once these components are detached, pull out the old hub assembly and install the new one, ensuring all bolts are torqued to specifications. Finally, reassemble the brake components, wheel, and lower the vehicle.
Is the axle on a 1991 tracker floating How do you remove it to replace the outer seal?
The axle on a 1991 Suzuki Tracker is a semi-floating design, meaning it has a shaft that is supported at both ends but relies on the wheel hub for additional support. To remove the axle to replace the outer seal, first, remove the wheel and brake components, then disconnect the axle from the wheel hub and the differential. Finally, pull the axle out of the housing, taking care to replace the outer seal before reassembling everything.
How do you remove a rear axle shaft on your Geo Tracker?
To remove the rear axle shaft on a Geo Tracker, start by safely lifting and supporting the vehicle on jack stands. Remove the rear wheels and the brake drum or rotor to access the axle assembly. Then, disconnect the axle retaining bolts and any associated components, such as the brake lines or differential cover if necessary. Finally, pull the axle shaft straight out from the housing, ensuring that any retaining clips are removed beforehand.
How do you replace a rear right axel in a 2002 4x2 Chevy s-10 pick up?
You have to take the differential cover off and remove a C clip that holds the axle shaft. that will allow you to pull out the axle (****** note the number of splines on the axle if ordering part!!!!)
