0
What else can I help you with?
How do you change the shift lamp in a Pontiac vibe?
To change the shift lamp in a Pontiac Vibe, first, disconnect the negative battery cable to ensure safety. Then, remove the center console trim by unscrewing any visible screws and gently prying it off. Locate the shift lamp bulb, which is usually found at the base of the gear shift, and replace it with a new bulb. Finally, reassemble the console and reconnect the battery.
Why won't your Pontiac Sunfire shift gears?
fluids are fine, no codes, and it wont shift past 2nd gear. any help?
What is wrong with a 1990 Pontiac LeMans if it starts fine but will not shift out of park?
The linkage for the brake pedal lockout is down on the shifter and when coke and coffee is spilled on the console, it runs on it and keeps it from working. You have to remove the console and clean the linkage.
How do you repair the console shift indicator light of a 2000 Olds Intrigue?
Just remove the console and you can get to it.
How do you change light bulb in the gear shift of 06 Pontiac grand prix?
Front Floor Console Replacement Removal Procedure 1. Apply the park brake. 2. Remove the floor console bolts from the sides of the console. Adjust the front seats as required. 3. Shift the transaxle to 2. 4. Remove the screw from the shift handle. Remove the shift handle. 5. Pull the floor console rearward slightly. Disconnect the electrical connector at the front of the floor console. 6. Remove the floor console. 7. Remove the wiring harness. 8. Remove the HUD switch, if equipped. 9. Remove the traction control switch. 10. Remove the accessory power receptacles. 11. Remove the armrest and the hinge. Installation Procedure 1. Install the armrest and the hinge. 2. Install the accessory power receptacles. 3. Install the traction control switch. 4. Install the HUD switch, if equipped. 5. Install the wiring harness. 6. Position the floor console to the vehicle. 7. Connect the electrical connector at the front of the floor console. Slide the floor console toward the front of the car. 8. Install the shift handle. Install the shift handle screw. 9. Shift the transaxle to P. Notice: Refer to Fastener Notice. 10. Install the floor console bolts. Adjust the front seats as required. Tighten the bolts to 10 N.m (89 lb in). 11. Release the park brake.
How do you change the Gear Shift Bulbs on a 2003 Pontiac Aztec?
To change the gear shift bulbs on a 2003 Pontiac Aztec, first, disconnect the negative battery cable to ensure safety. Remove the gear shift trim by carefully prying it away from the console, then locate the bulb sockets beneath the gear shift. Twist and remove the old bulbs, replacing them with new ones, and reassemble the trim before reconnecting the battery. Test the new bulbs to ensure they work properly.
How do you get under shift console in 2007 chrysler sebring to press transmission rance sensor to get out of park?
Remove the bolts holding the console down and remove.
How do you remove the console shift knob on an AT 1993 Olds Achieva?
To remove the console shift knob on the AT 1993 Olds Achieva, first pry the cover from the top of the shift knob. Then, access the single screw inside the cover of the shift knob and turn it counter-clockwise to release the knob.
How do you change throw-out bearing 98 Pontiac Sunfire?
To change the throw-out bearing on a 1998 Pontiac Sunfire, first, you'll need to remove the transmission. Begin by disconnecting the battery, draining the transmission fluid, and removing the necessary components such as the driveshaft and shift linkage. Once the transmission is unbolted and supported, you can access the clutch assembly, where the throw-out bearing is located. Remove the old bearing from the clutch fork and install the new one, then reassemble by reversing the steps.
How do you remove a shift console from a 1998 Oldsmobile intrigue?
To remove the shift console from a 1998 Oldsmobile Intrigue, start by disconnecting the battery for safety. Next, remove any screws or clips securing the console, often found around the gear shift area and under the armrest. Gently pry off the console using a trim removal tool to avoid damaging the surrounding panels. Finally, disconnect any electrical connectors attached to the console before fully lifting it out.
How do you change a shift console bulb on a 2002 Jeep Liberty?
Begin by removing the 2002 Jeep Liberty shift console retaining bolts. Lift the shift console up and the light bulb will be visible. Take hold of the light bulb, push in and turn at the same time to remove it. Reverse the process to install your new shift console light bulb.
How do you change the shift knob on a 1997 Pontiac sunfire 5-spd?
there is a large metal staple type fastener on the frt of the knob that can be pulled out with a screw driver
