answersLogoWhite

0

remove horn button (or horn ring) remove large nut in centre of wheel, get a steering wheel puller kit from an auto parts store (buy or rent) install one long bolt into small hole in centre hub of wheel (they come with the kit), then put main part of puller in place. next install second long bolt into small hole on other side of wheel hub. Now tighten main puller centre bolt. it should be pushing on stud that you removed the large nut from. if it gets very tight without the steering wheel "poping" loose, hit the main bolt with a hammer, this should cause the steering wheel to pop loose.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Where is the choke on a 1967 f10 Chevy pickup?

i have a 67 gmc 910 pickup. the choke in mine is on the dashboard above the steering wheel and to the right. it is a white plastic knob with the letter "C" on it.


How do you replace horn ring on 67 vw?

To replace the horn ring on a 1967 VW, first disconnect the battery to ensure safety. Remove the steering wheel by loosening the central nut and using a steering wheel puller if necessary. After removing the wheel, detach the old horn ring by unscrewing it from the steering column. Install the new horn ring by reversing the process, ensuring all connections are secure before reconnecting the battery and testing the horn.


How do you replace a Turn Signal Switch on a 1967 Chevelle?

the steering wheel has to come off and then you will be able to see how it comes out.


How do you remove the power steering gear box from a 1967 Barracuda?

take the hoses off of it and unbolt the steering column from the box, pull the steering link arm off the bottom of the box and then unbolt the box from the frame and pull it out.


Will a gear box from a 1968 Chevy truck work in 1967 Chevy truck?

Need more info, manual steering gear box, power steering gear box, 3 speed standard transmission box, or 4 speed transmission box? The truck has a 3 speed manual transmission and power steering gear box thanks The steering gear box will interchange.


What are the release dates for Wheel-Dealer - 1967?

Wheel-Dealer - 1967 was released on: USA: 1967


How do you remove steering wheel 1967 vw beetle?

Remove Wolfsburg badge, remove brown cable. Unscrew nut size 32 from the shaft. Take away the wheel. On some models (Type I's and Karmann Ghias), the brown cable is not connected to anything, it sits in an insulating sleeve in the end of the shaft and all you see is a brass contact. If you ground the brown wire with your wrench/socket, the horn will sound. A little penetrating oil between the shaft splines and the wheel hub will make life easier.


How do you remove a harmonc balancer 1967 Chevy 327 cid?

That requires a special puller. Some parts stores will rent it to you.


Will a 67 chevelle steering wheel fit a 64 c10?

A 1967 Chevelle steering wheel may fit a 1964 C10, but compatibility largely depends on the steering column and the spline count of the wheel. Both vehicles use a similar design, but there may be differences in the mounting hardware or size that could require modifications. It's advisable to check the specific spline count and diameter of both wheels to ensure a proper fit.


How do you replace the turn signal switch on a 1967 ford mustang?

You have to pull the steering wheel with a puller to get to the switch. Disconnect the battery The HUGE horn button is removed by pressing and turning remove the nut from the steering column and then pull the steering wheel you might need to disassemble more of the column to get the wiring harness through, but not too much


How do you remove rear seat out of a 1967 Chevy Nova?

To remove the rear seat from a 1967 Chevy Nova, start by locating the seat bottom clips or bolts, usually found at the front edge of the seat. Pull up on the seat bottom to disengage it from the clips or remove the bolts if applicable. Once the bottom is removed, the seatback can be unbolted from the rear or sides, depending on your model. Finally, lift the seatback upwards to remove it from the vehicle.


How do you connect the power steering hoses on a 1967 Chevy Impala?

you have 2 hoses .a pressure line and a return line .the pressure line is steel while the return is rubber hose.