0
Removing a broken small steel screw from the aluminum distributor housing will be a challenge. Start with removing the distributor from the engine so you can work with it in the bench/vise. If there is some of the broken screw exposed you can heat the housing and grab the broken screw with vise grips gently working it back and forth until it loosens up. Or, if you're good with a drill and have good drill bits, try drilling out the broken piece starting with the smallest drill bit you have. You have to drill it dead center or the bit will walk of center into the soft aluminum. Clean out the remains with the appropriate tap. If all else fails, turn in the distributor for a re-manufactured one and don't over tighten the screws during assembly. A dab of anti-seize on the threads wouldn't hurt.
What else can I help you with?
Is there a screw keeping the distributor from turning on a 1998 Dodge Dakota 3.9L V6?
Yes, there is a bolt and a plate that holds the distributor down.
How do you adjust vacuum advance on a dodge electronic distributor?
pull the hose off the vacuum advance and some of them have a set screw inside the hole.
What is the best broken screw removal tool to use for extracting a stubborn screw?
The best broken screw removal tool for extracting a stubborn screw is a screw extractor. It is designed to grip onto the broken screw and twist it out of the material.
Where is the number one on the distributor 1995 dodge ram 1500?
the number one is located to the right (towards engine)of the left instalation screw of the cap. if you are able to see it it has 1 on the cap.
Screw holes on distributor cap are stripped?
As the screw holes on the distributor caps are used to hold the cap down, when stripped, the cap could be JB Weld. ?æRe-drill the screw hole once the weld cures.
What is the best way to remove a broken screw from a surface?
The best way to remove a broken screw from a surface is to use a screw extractor tool. This tool is designed to grip onto the broken screw and twist it out of the surface. It is important to use the correct size extractor and to apply steady pressure while turning it counterclockwise to remove the broken screw.
Can a vehicle operate normally with only one screw holding the distributor cap down?
No only one screw holding the distributor down will cause the cap to be crooked and damage to the cap and rotor will result
How can I unscrew a broken screw?
To unscrew a broken screw, you can try using a screw extractor tool or drilling a small hole into the screw and using a screwdriver to remove it. Another option is to use a rubber band or super glue to grip the screw and turn it counterclockwise.
How do you remove a screw that broke off from the distributor and is now stuck inside of the hole that the screw goes into?
Get an Easy Out (left-handed) reverse drill bit that is smaller than the shaft of the broken screw. Run your drill counter-clockwise at a low rpm, while keeping the bit centered on the broken end of the screw. You might want to drill a smaller pilot hole with a normal drill bit first. At some point after cutting and weakening the inside of the broken-off screw end, the left-handed drill bit will catch on the metal and twist it out. I think there are videos of how this is done online. Getting the bits can be expensive, but they're invaluable for something like this.
How can I remove a broken screw without using an extractor?
One way to remove a broken screw without using an extractor is to drill a small hole into the center of the screw and then use a screwdriver to turn it out.
How can I effectively remove a broken screw head using a screw extractor tool?
To effectively remove a broken screw head using a screw extractor tool, follow these steps: Drill a small hole into the center of the broken screw head using a drill bit slightly smaller than the screw extractor tool. Insert the screw extractor tool into the drilled hole and turn it counterclockwise to grip the screw head. Use a wrench or pliers to turn the screw extractor tool counterclockwise to remove the broken screw head from the material. Apply steady pressure and avoid using excessive force to prevent further damage.
How can I effectively remove a broken screw from wood?
To effectively remove a broken screw from wood, you can try using a screw extractor tool or drilling a small hole into the screw and using a screwdriver to turn it out. Another method is to use a hammer and a nail punch to tap the screw out from the wood.
