0
To replace the tail lamp assembly in a Pontiac Vibe, first, open the rear hatch and locate the access panel or screws securing the tail lamp. Remove the screws or panel, then gently pull the tail lamp assembly away from the vehicle. Disconnect the electrical connector and replace the old assembly with the new one, reconnecting the electrical connector and securing it in place with screws. Finally, test the new tail lamp to ensure it functions properly before closing the access panel.
What else can I help you with?
How do you replace the tail light lamp on a Pontiac Aztec?
It is a Pontiac Aztek. Light a match and get some marshmallows.
How do I replace tail lamp 2003 Volvo v70?
To replace the tail lamp on a 2003 Volvo V70, first, open the rear hatch and locate the tail lamp assembly. Remove the screws or clips securing the assembly, then gently pull it out from the vehicle. Disconnect the electrical connector and replace the bulb or the entire assembly as needed. Reconnect the electrical connector, position the assembly back into place, and secure it with screws or clips before closing the hatch.
How do you change the tail light on a 2003 Pontiac Vibe?
Remove carpet inside trunk that covers tail ligh assembly, then unbolt tail light assembly, remove the assembly and bulb fixture of the bulb you want to replace, replace bulb and re-install in reverse order.
How do replace tail lamp bulb 2005 Xterra?
how to replace tail lamp 2005 xterra
How do you replace a left rear turn signal light on a 2001 Blazer?
For any Gen II (1995 - 2005) Blazer, Jimmy, or Bravada, it's all the same. Open the hatch. On the side of the door jamb, you'll see two screws - those hold the tail lamp assembly in place. Remove those, and the whole tail lamp assembly will come out. The bulb holders are in the back of the tail lamp assembly - rotate them counterclockwise, and they will come out. Then you can replace the bulb, put the lamp holder back into the tail lamp assembly, and the installation is the opposite of removal. Pretty simple stuff.. only tools required are a short Phillips screwdriver.
How do you replace tail light for 2006 Pontiac torrent?
1) Open hatch. 2) Remove two screws at tabs on rear of light assembly. 3) Pull light assembly away from fender in direction perpendicular to side of vehicle. 4) turn bulb/lamp socket and remove from light assembly. 5) Pull bulb from socket. 6) Replace bulb. 7) Test lamp. 8) Installation is reverse to above.
How do you replace a brake light bulb for a 2002 dodge ram 1500?
Lower the tailgate. Remove the two screws on the inside to the side of the lamp assembly with an torx wrench. The tail lamp assembly will pop out. Remove the four screws on the backside of the tail lamp with a Phillips head screwdriver. You now have access to the bulbs.
How do you replace the rear turn signal bulb on a 2007 Lincoln MKX?
Replacing tail/stop/turn/sidemarker/backup lamp bulbs The tail/stop/turn/sidemarker/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb. Note: Your vehicle is equipped with a backup lamp assembly containing integral multiple light emitting diodes (LED). See your authorized dealer for the replacement LED module. 1. Make sure the headlamp switch is in the off position and then open the liftgate to expose the lamp assembly bolts. 2. Remove the two bolts from the lamp assembly. 3. Carefully remove the lamp assembly away from the vehicle by pulling the assembly straight out to expose the bulb socket. DO NOT TIP THE LAMP ASSEMBLY SIDEWAYS. 4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two bolts.
How do you remove the tail light bulbs from a 1994 Pontiac Trans AM?
To remove the tail light bulbs from a 1994 Pontiac Trans Am, first, open the trunk and locate the tail light assembly. Remove any screws or bolts securing the assembly, then carefully pull the assembly out from the body of the car. Twist the bulb socket counterclockwise to release it from the assembly, and then pull the bulb straight out to replace it. Reassemble the tail light by reversing the steps.
How do you replace the rear tail light on a 2004 Pontiac aztek?
To replace the rear tail light on a 2004 Pontiac Aztek, first, open the rear hatch and locate the tail light assembly. Remove the screws or bolts securing the assembly, then gently pull it away from the vehicle. Disconnect the electrical connector and remove the old bulb by twisting it counterclockwise. Insert the new bulb, reconnect the electrical connector, and secure the tail light assembly back in place.
How do you replace the rear left stop light bulb on a 2000 Mercedes Benz Ml320?
Hi there,This is really quite simple. You will need to remove theentire tail lamp assembly to do this. open the rear tail gate. locate the 2 10mm nuts (black plastic) on the right side of the leftbrake lamp assembly, (should also have a slotfor a Phillips screw driver). Remove these 2 nuts. Tail lamp assembly is then pressed into a grommetat the rear. You will need to pull straight out towardsthe rear. (Might be tight) I sometimes use a plasticwedge to help pry off tail lamp assembly. Once tail lamp is out, just depress the 2 plasticclips to release the bulbs from inside the assembly. And replace needed bulbs. (brake light will be the top one)(12v 21w) single filament. .
How do you replace 2002 Mercedes Benz ML 500 stop light bulb?
Hi there, This is really quite simple. You will need to remove the entire tail lamp assembly to do this. open the rear tail gate. locate the 2 10mm nuts (black plastic) on the right side of the left brake lamp assembly, (should also have a slot for a Phillips screw driver). Remove these 2 nuts. Tail lamp assembly is then pressed into a grommet at the rear. You will need to pull straight out towards the rear. (Might be tight) I sometimes use a plastic wedge to help pry off tail lamp assembly. Once tail lamp is out, just depress the 2 plastic clips to release the bulbs from inside the assembly. And replace needed bulbs. (brake light will be the top one) (12v 21w) single filament. Hope this helps.
