0
What else can I help you with?
Why does the security light stay blinking on your 2004 keyless entry Camry Toyota after you turn off the car?
The security light flashes when a programed key is not installed in the ignition, when you insert a programed immobilizer key in the ignition the security light will go out, the light flashes as a theft deterrent
The security light on my 93 cadillac deville flashes when i take the keys out of the ignition. how do i shut that off?
A flashing Security light is indicating that the security system on your car is active.
Why would the parking lights flash and a clicking noise continue after the ignition is off in a 1999 Oldsmobile Aurora The security light flashes also. Related?
Will This car start and run because mine will not. and it does the same thing If you have found out anything please respond and let me know thank you
Why does your 1999 Nissan maxima security light flashes when ignition is offthen goes solid on with ignition on and while crankingand car will not start?
I forgot to tell you after you connect the battery with the key in start position try to start the car after you reconnect the battery
What might cause a 1998 Sierrea SLE not to startSecurity light flashes on message center if that matters?
If the security light is flashing you need to change the ignition switch it self. It is likely worn out.
How do you get the codes out of a 1990 dodge ram 250?
Cycle the ignition on/off/on/off/on and count the flashes of the check engine light. A pattern of two flashes, pause, two flashes would be a code 22.
How do you tell if the instrument cluster is out on a Oldsmobile cutlass supreme?
I have a 90 cutlass supreme. Mine has been going goofy for some time now. If it blacks out, flashes off and on, or shows different readings on fuel gauge, odometer or speedometer then you have problem. I took it out and looked for loose plug wires(1 plug) or cicuits. Found none. Needs replaced. Can sometimes be found on Ebay for cheap price. If so make sure it right one!!!
How toprogram security warning light in a 1998 Buick regal ls?
To program the security warning light in a 1998 Buick Regal LS, you typically need to use the vehicle's ignition system. Start by turning the ignition to the "ON" position without starting the engine. Then, press and hold the "lock" button on the key fob for about 15 seconds until the security light flashes, indicating programming was successful. If your vehicle has specific security features or a factory alarm, consult the owner's manual for detailed instructions.
How do I get the ECM to recognize the replaced Ignition Switch?
You replace the ignition cylinder and then turn the ignition (with key) to on position. All dash lights will light up in the on position. After a few seconds only the security light will flash. Leave the ignition on for 10 minutes while the security light flashes. At the end of the 10 minutes the security light will go out. This will be the first cycle of reseting the E.C.M. to read the new cylinder and ignition system replacement. At this point you do this process two more times. This will take proximately 30 minutes. At the end of all three cycles the car should come on. If you want someone to walk you through it E mail me at archuleta67@gmail.com.
How do you find the fault codes on your 1995 grand caravan?
Turn the ignition key on,off,on,off then on and count the the flashes of the check engine symbol .It flashes the first number then there is a short pause then it flashes the second number. Example 24 ( two flashes and a pause then four flashes). Look up this number in Chilton's/Haynes or the shop manual for the vehicle
P0302 check engine light flashes on a 2002 Oldsmobile sillhouette?
Trouble code P0302 means:Cylinder 2 misfire detected
How do you read trouble codes in a 1991 Oldsmobile ninety-eight?
To read trouble codes in a 1991 Oldsmobile Ninety-Eight, you need to locate the diagnostic connector, typically found under the dashboard near the steering column. Use a jumper wire to connect terminals A and B of the ALDL (Assembly Line Diagnostic Link) connector. Then, turn the ignition key to the "On" position without starting the engine; the check engine light will blink the trouble codes in a series of flashes. Count the flashes to interpret the codes, which can be referenced in a repair manual for further diagnosis.
