answersLogoWhite

0

To test the coolant temperature sensor on a 1992 Oldsmobile V6 3300 engine, first, locate the sensor, which is typically near the thermostat housing. Use a multimeter to measure the resistance across the sensor terminals while the engine is cold and again when it's warmed up, comparing the readings to the manufacturer's specifications. If the resistance values are outside the specified range, the sensor may be faulty and should be replaced. Additionally, you can check the sensor's output by monitoring the engine's temperature gauge for proper operation.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

How do you reset the low coolant level light on 92 Oldsmobile achieva v6 3300 engine?

If the coolant system (radiator and reservoir) is full and the light remains on, the probe on the coolant level sensor is probably dirty. Remove it from the radiator, clean it gently with brake clean and an old toothbrush, re-install it, refill coolant system and you should be good to go.


How do you replace spark plug wires on a 3300 oldmobile engine?

To replace spark plug wires on a 3300 Oldsmobile engine, open the hood and remove the wires from the end of the engine. The number of spark plug wires most often corresponds to the number of cylinders your engine has.


What is the Weight of a 1992 delta 88 Oldsmobile?

3300 lbs


Does the ECM and the fan work off the same coolant sensor on a 92 grand am 3300?

I could be completely wrong, but I think they share the same sensor. If there's two sensors for the coolant, one usually goes to a gauge and the other is used by the computer, which in turn controls the fan activation and speed.


What is the firing order for 1993 olds 3300 engine?

The firing order for the 1993 Oldsmobile 3300 engine is 1-2-3-4-5-6. This means that the cylinders fire in that specific sequence, which is crucial for the engine's proper operation and performance. The engine is a V6 configuration, and knowing the firing order is important for tasks such as troubleshooting and ignition system maintenance.


What are some possible problems on a 1993 Buick Skylark 3300 that can allow the engine to rotate but not start and no trouble codes?

I took it to a shop. It was the crankshaft position sensor.


Where is the ignition control module located on a 1990 Oldsmobile Cutlass Calais?

Is the Claias 2.3L 2.5L or 3300?


Where is the cam sensor for a 1990 Oldsmobile cutlass ciera?

i have a 90 cutlass ciera with a v6 3300 and just replased that. it is called a combanation sensor. its the crankshaft and cam together located at the back of the harmonic balancer attached to the block. it has 2 bolts on the right side holding it to the block a one in the middle to hold the sensor in place and the sensor sits in it and faces the harmonic balancer on the back of the interrupter rings


Having timing chain problems for a 1990 Buick century 3300 engine?

How do the timinh marks line up for buick ventury 1990 with a 6cyl 3300 engine


Where is the oxygen sensor located on the engine of a Buick 1993 Skylark 3300 engine. I would appreciate a simple drawing of the part of engine where the sensor is to be replaced. Thank you very much?

A GM dealer's service center (if they're still in business) would be able to show you. Also, Amazon.com might have Buick repair manuals (dirt cheap by now...).


What is the meaning of 3300 engine?

3300 refers to the total volume of the combustion chamber(s) being displace when the engine cycles through. They take the volume of each cylinder and add them up and get a total.3300 is the total number of cubic centimeters that is being displaced; in other words, the engine's displacement. It's equivalent to hearing some engine referred to as a "3.3 liter".


What else can you do to get the fan to work on your 1992 Buick Century 3300 I replaced the coolant temp sensor but still not coming on Please help?

Run a wire from the positive terminal on the battery to the fan motor. If the fan will not run when hot wired, the motor is burned out and will have to be replaced. If the fan will run when hot wired, check the fan motor fuse. It us probably in the engine compartment near the battery.