answersLogoWhite

0

i don't think you need to remove the enigine.....i also own a 2003 galant and i had mine done at a dealership......costed around $700 and i got it back in a couple of days.....results and prices may vary...

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you remove Mitsubishi Galant Axle?

Unbolt it.


How do you change the foglamp bulbs on a 2004 Mitsubishi Galant?

Safely jack the car up, remove lamps,replace bulbs.


How do you change a wiper motor on a 2005 Mitsubishi galant?

The wiper motor is located on right rear of engine, hood up. Remove old wiper and replace before tightening the bolts test their location to mount.


How do you reset the check engine light on a 1996 Mitsubishi galant?

Remove negative polar of battery and replace after a couple of minutes. FYI your car will ride rough for about a half hour while the computer re learns itself (reset)


Where is the cabin air filter located on a 2001 Mitsubishi Galant 4-cylinder 24 liter engine and how do you replace it?

It is located behind the glove box. Remove the glove box completely and it is attached with two screws. Hope this helps


Where is the starter located on 02 Mitsubishi Galant?

The starter on a 2002 Mitsubishi Galant is located on the passenger side of the engine bay, near the bottom of the engine block. It is mounted to the transmission bell housing and can be accessed from underneath the vehicle. You may need to remove some components, such as the air intake or heat shield, to reach it more easily.


Where is the expansion valve on your Mitsubishi Galant?

Expansion valve is located on the A/C Evaporator Core. Most of the times you have to remove the whole dash to reach it/ replace it. Good luck.


How do you replace alternator on Mitsubishi Galant 2000?

To replace the alternator on a 2000 Mitsubishi Galant, first disconnect the negative battery cable and remove the drive belt by loosening the tensioner. Unbolt the alternator from its mounting bracket and disconnect the electrical connectors. Install the new alternator by reversing the removal steps, ensuring all connections are secure, then reattach the drive belt and reconnect the battery. Finally, start the engine to confirm the new alternator is functioning properly.


Where is the exhaust manifold on a 1996 Mitsubishi Galant s?

The exhaust manifold on a 1996 Mitsubishi Galant S is located on the engine block, typically on the side of the engine facing the firewall. It connects to the exhaust ports of the engine cylinders and directs exhaust gases to the exhaust system. To access it, you may need to remove components like the intake manifold or other nearby parts, depending on the engine configuration.


How do you replace the instrument panel lights in 2002 Mitsubishi Galant?

To replace the instrument panel lights in a 2002 Mitsubishi Galant, first, disconnect the negative battery terminal for safety. Remove the screws securing the instrument panel bezel and carefully pull it away to access the gauge cluster. Unscrew the cluster from the dashboard, then twist the bulb sockets counterclockwise to remove them and replace the old bulbs with new ones. Reassemble the cluster, bezel, and reconnect the battery.


How do you replace the headlight in a 2001 Mitsubishi Galant?

To replace the headlight in a 2001 Mitsubishi Galant, first, open the hood and locate the headlight assembly. Remove the screws or clips securing the assembly, then carefully pull it out. Disconnect the wiring harness from the old bulb and replace it with a new headlight bulb, ensuring not to touch the glass with bare hands. Finally, reassemble the headlight assembly and secure it back in place.


How do you change carburetor on 2002 Mitsubishi Galant?

To change the carburetor on a 2002 Mitsubishi Galant, first, ensure the engine is cool and disconnect the battery. Remove any components obstructing access to the carburetor, such as air intake and throttle linkages. Unscrew the carburetor from the intake manifold, detach any fuel lines, and replace it with the new unit, ensuring all gaskets are properly seated. Finally, reattach all components, reconnect the battery, and test the engine for proper operation.