0
What else can I help you with?
How do you change the idler pulley on 1994 Cadillac eldorado?
Take the belt off, un-bolt the idler pulley, bolt the new pulley on, and finally put the belt back on and Viola!!
What is the pulley under the alternator in a 1994 Chevy caprice 5.7L and how hard is it to change?
Are you talking about the "idler pulley"? They are quite simple to change. Loosen the serpentine belt by using a socket on the center of the tensioner pulley, slide the belt off the idler pulley, use a socket to pull the center bolt of the idler pulley and replace the pulley with a new one.
How do you change the idler pulley on a 1994 Ford Bronco?
To change the idler pulley on a 1994 Ford Bronco, first, ensure the engine is off and cool, then disconnect the negative battery cable. Use a socket wrench to relieve tension on the serpentine belt by rotating the tensioner pulley, and remove the belt from the idler pulley. Unbolt the old idler pulley using the appropriate socket size, then install the new pulley and reattach the serpentine belt following the routing diagram. Finally, reconnect the battery cable and start the engine to ensure everything is functioning properly.
Why is your new idler pulley squeaking on your 1994 GM Jimmy?
I assume you mean the idler pulley on your timing assembly, if this is the case then the belt is too tight loosen tensioner pulley. if you mean the automatic tensioner pulley for your alternator and A/C and the like, the you probably need a new tensioner] Good Luck
Where is the idler pulley located on a 1994 GMC Sierra?
i dont really know-but to find out just look it up on google!
How do you change the idler pulley on a 1994 explorer?
On the belt routing diagram under the hood (near the grille, but under the hood) you will find the location of the 'tensioner' pulley. You need to get a 15mm socket and place it on the bolt on the tensioner pulley. Then use a ratchet to put clockwise pressure on the bolt to loosen the tension on the belt. This will allow you to remove the belt from the idler pulley, remove the bolt, put on the new pulley. Now put clockwise pressure on the tensioner pulley again to put slack in the belt so you can slip it around the new idler pulley. You're done.
How will you know if the idler pulley needs replaced on 1994 Mercury Grand Marguis?
Remove belt and check to see that it rotates freely and smoothly
How do you change idler bearing on 1994 Pontiac sunbird le 2.0 engine step by step?
To change the idler bearing on a 1994 Pontiac Sunbird LE with a 2.0 engine, first, disconnect the negative battery cable to ensure safety. Next, remove the serpentine belt by loosening the tensioner pulley. Once the belt is off, take out the idler pulley by unscrewing the bolts that secure it, then replace the old bearing with a new one or install a new idler pulley if necessary. Finally, reassemble everything by reversing the steps, ensuring the serpentine belt is properly aligned, and reconnect the battery.
How do you loosen the idler pulley on a 1994 landcruiser?
The idler pulley is attached by a 14mm hex head bolt. Although the pulley turns counter-clockwise, suggesting that the bolt might be left-handed threads, it is in fact right-handed. A 1/2" drive ratchet with a 14mm socket will loosen the bolt if turned in a counter-clockwise direction. Be sure and loosen the belt tensioner, located below the alternator, and loosen but not remove the other alternator bolts, prior to removing the idler pulley.
How do you remove the serpentine belt from a 1994 Chevrolet Cavalier?
Using a 15mm wrench, turn the bolt in the center of the idler pulley clockwise to relieve tension and remove the belt.
How do you replace fan belt 1994 C 1500 4.3 motor?
Get a socket and a ratchet. Find out what socket fits the nut on the idler pulley. The whole idler arm should rotate counterclockwise. That'll relieve belt tension so you can replace the belt.
How do you remove the serpentine belt drive idler pully on a 1994 Ford Ranger 4 liter engine?
You have to buy the assembly with the mounting bracket. You can't just buy the pulley itself. You buy the whole assembly and remount it to the engine. that is not the whole truth. you can buy the pulley by its-self. the part is sold on eBay for $33, my father is having this problem and we have to replace the pulley
