0
Go to your local Pep Boys or similar Auto parts store, and purchase two new struts. You will have to find the exact struts for your car, as the struts are different if you have a spoiler or if you have a rear wiper, and from year to year.
With the new struts in hand, as well as a flat head screwdriver or needle nosed pliers, open the trunk, have the new strut out and near the side you will work on first. There will be one metal clip on each strut holding it to the ball joint, pry this off with the screwdriver or the pliers. Support the trunk with one hand and then pull the old strut from the joints. The one remaining strut can not hold up the trunk, so you will have to continue to support it. Set the old strut aside, then grab the new one, don't mess with the clips on this one, simply press the ends onto the joints, they might take some force, but not too much. Repeat this process on the other side and you are done.
What else can I help you with?
How do you replace rear struts on 2001 Cougar?
To replace the rear struts on a 2001 Mercury Cougar, first, safely lift the vehicle and remove the rear wheels. Then, disconnect the lower strut bolts and upper strut mounting nuts found in the trunk. After removing the old struts, install the new struts by reversing the disassembly process, ensuring all bolts are torqued to the manufacturer's specifications. Finally, reattach the wheels and lower the vehicle.
Where is the module located on a 1993 Mercury Cougar?
In the trunk
How to change the rear struts on a 2001 Mercury Cougar?
To change the rear struts on a 2001 Mercury Cougar, first, safely lift and support the vehicle on jack stands. Remove the rear wheels, then unbolt the lower strut mount and detach the upper strut mount inside the trunk. Replace the old struts with new ones, ensuring they are securely fastened, then reassemble the components in reverse order. Finally, reinstall the wheels, lower the car, and perform a test drive to check for proper installation.
Why does the trunk not open by pushing the button on the inside of a 99 mercury cougar?
if i don't have the key to open the trunk or the push button does not work from the inside of the car to open the trunk of a 1999 mercury cougar, could i be able to bypass the button or switch to open it?
How do you Replace a 1999 Ford Contour trunk strut?
To replace the trunk strut on a 1999 Ford Contour, first, securely prop the trunk open to prevent injury. Use a socket wrench to remove the bolts securing the old strut at both ends. Carefully detach the old strut and align the new strut in place, securing it with the bolts. Finally, repeat the process for the other strut if necessary, ensuring everything is tightened properly before closing the trunk.
How do you replace vw beelte trunk strut?
These are the things that you should have: Screwdriver Hood Prop Trunk Strut And these are some general steps: 1. Open the trunk. 2. Prop open the trunk 3. Remove the retainer bolts from the top and unscrew lower end of the old shocks. 4. Remove the weak trunk strut 5. Install the new strut. Replacing struts in pairs is recommended. 6. Remove prop rod. 7. Inspect and test the trunk to verify the trunk strut repair.
Anyone know of a ground spot for 1999 Mercury cougar for amplifier?
trunk hinges or seat bolt
Where is the keyless entry code for the 1990 mercury cougar?
its in the trunk on a sticker or under the hood or inside the door
How do you replace the trunk strut on a 1998 Acura Integra?
unbolt the old one put in the new one
Where is the fuel pump relay located on a 97 mercury cougar?
fuel pump relay is located on the left side trunk and it is a small panel up towards the trunk.
Does a 1997 Mercury Cougar have a emergency cutoff switch?
There is an inertia switch / fuel cutoff switch in behind the trunk liner , on the left side of the trunk ( there is an access hole )
How do you replace the rear strut on 2002 sable gs?
To replace the rear strut on a 2002 Mercury Sable GS, first, safely lift and support the vehicle using jack stands. Remove the rear wheel, then detach the strut from the lower control arm and the top mount inside the trunk by removing the nuts. Install the new strut by reversing the removal process, ensuring all bolts are tightened to the manufacturer's specifications. Finally, reattach the wheel and lower the vehicle, checking for proper alignment.
