answersLogoWhite

0

if you didnt bend it during removeal then it is fine to re-use it.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you change a wheel bearing on a Pontiac grand prix gtp?

You have to get a new hub with the bearing in it already.


Can the bearings in the alternator for 2002 Pontiac sunfire be changed?

probably it can be changed but if you change the whole alternator you will gain a new alternator for your engine in opposite of changing only the bearing which is not guaranteed.


How do you change the wheel bearing hub assembly on a 97 Pontiac Grand AM?

Fron or rear?


How do you change a rear wheel bearing on a 2000 Pontiac Montana?

You need to replace the rear wheel hub - bearing and speed sensor inclusive


How do you change an abs traction control sensor in the left front hub of a 1999 Pontiac grand am?

Need to change the whole bearing...


How do you change the ABS speed sensor on a 1993 Pontiac Bonneville also need to know the do's and do not's for this procedure?

The speed sensor may be built into the hub bearing. In that case the whole hub bearing needs to be replaced.


How we can change our bearing?

To change your bearing, you need to turn left, right or make an about turn in the given vessel that you are travelling in.


How do you change a radiator on a 2001 Pontiac Montana?

Before changing the radiator on a 2001 Pontiac Montana the coolant must first be drained. After the drain remove the radiator mounts, fans, and hoses. Pull the radiator upwards.


How to Change a wheel bearing on a 92 Toyota Paseo?

Changing the wheel bearing in a 1992 Toyota is simple. All you do is remove the wheel hub, take off the C clips, use a hammer to remove the bearing which is connected to the C clips. You can also take them into a shop and have them removed.


How do you a change a battery in a 2002 Pontiac Montana?

how do you change a battery on a 2002 Pontiac Montana


How do you change a AC compressor bearing in a 2000 Chevy Cavalier?

You cannot change the compressor bearing, however, you can change the clutch bearing. Which one is bad? Is there a noise when the clutch is engaged, or not engaged?


How do you change rear wheel bearing on 1999 alero?

How do you change rear wheel bearing on 1999 alero?

Trending Questions
Drivers side outer tie rod end how to change it on a 86 Ford Ranger 2.3? What size is an 2004 escalade fog light bulb? What does it mean when the ABS light comes on and stays on in a 1996 Chevy Blazer LS? Is it possable to get a cavalier to have more than 500hp with out a turbo? Small crack in the center of one piston is this OK? Where is the carburetor located on a 1997 Dodge Neon and where do you spray the starting fluid? What is the torque when replacing front wheel bearings on a 1995 Ford F150 four wheel drive with manual hubs? Where is radiator drain plug on 2002 ford expedition? What year was the El Camino available in convertible? How many gallons does the gas tank in the 2011 Jeep Patriot hold? If a 93 Aerostar won't select vent or heat and the air just comes through the defroster is it the selector? How do you chage ignition switch on a 1997 Chevy pickup truck 4x4 1500? When I was loosening the tension pulley to replace the serpentine belt on a 93 Dodge Dynasty the bolt that holds the pulley to the engine sheered off so now can I drill that out or is there no hope? Does the 2004 Nissan frontier v6 3.3l have an interference engine? Where is the wheel tilt on 1997 mercury villager? Need a vacuum hose diagram for a 1997 Dodge truck 1500? How do you replace a serpentine belt in a 2000 jeep wrangler? Will a bad thermostat prevent heater from working correctly? Sometimes it will change gears and sometimew it won't sometimes it will go into reverse and some times it won'tis there a computer chip for shifting? What does a lightning bolt sign mean on a dodge caliber?