answersLogoWhite

0

Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you remove lower ball joint on 2003 GMC savana?

how to remove lower ball joint on 2003 gmc savana van


How do you remove a 1997 GMC Safari upper ball joint?

Actually the upper one is the easiest, Jack up the vehicle, remove the tire, remove the nut on the end of the ball joint, sometimes you have to cut the nut to remove it. I have found at this point it easier to cut the rivets off the top of the balljoint (the new will have bolts) using either a chiesel and hammer or an air hammer, using a ball joint seperator separate the joint from the steering knuckle at this point you shoud be able to pull the ball joint straight up from the A-arm just reverse the procedure making sure to use all the new attaching hardware and be sure to torque everything to spec's


How do you change the upper control arm bushings on a 1994 gmc siera 2500 4x4?

Remove control arm from vehicle. If ball joint is pressed, use ball joint press (or hammer) to remove ball joint. If it is held in by rivits, destroy rivits and remove ball joint. Bushings may be removed and installed with ball joint press; use your head (ie: you can use a socket if there is not a ball joint press adapter that fits control arm bushing, etc.). Install new bushing STRAIGHT! Install all other parts in reverse order of removal. You should get an alignment after finished.


How do you change a lower ball joint on a GMC Vandura 1 ton van?

To change the lower ball joint on a GMC Vandura 1-ton van, first, lift the vehicle and securely support it on jack stands. Remove the wheel, then detach the brake caliper and rotor to access the lower control arm. Unbolt the lower ball joint from the control arm and steering knuckle, then press out the old joint using a ball joint separator tool. Install the new ball joint by reversing the steps, ensuring all bolts are torqued to the manufacturer’s specifications.


How do you change the lower ball joint in a 95 gmc vandura van?

To change the lower ball joint in a 1995 GMC Vandura van, first, safely lift and support the vehicle on jack stands. Remove the wheel and brake components to access the lower control arm. Disconnect the lower ball joint from the control arm and steering knuckle, using a ball joint separator if necessary. After removing the old ball joint, press in the new one, reassemble the components, and ensure everything is properly torqued before lowering the vehicle back to the ground.


How do you remove the automatic shifter cable from a 1997 GMC Sierra 1500?

How do you remove the automatic shifter cablein a 1997 GMC sierra 1500


How do you replace a upper ball joint in a 2006 gmc envoy?

To replace the upper ball joint in a 2006 GMC Envoy, start by safely lifting the vehicle and removing the front wheel. Disconnect the sway bar link and unbolt the upper control arm from the knuckle. Press out the old ball joint using a ball joint separator tool, then install the new ball joint in reverse order. Finally, reassemble everything, ensuring all bolts are torqued to manufacturer specifications.


How do you change lower ball joint on 1996 gmc sonoma?

you have to use a press to pop out the ball joint, you might consider removing your a arm and bring it to a shop with press so that you can have your new ball bearing pressed


How do you remove the bench seat on a 1997 GMC Sonoma SL?

remove the bolts buddy.... lol


How replace 1997 gmc savana van door lock?

how do I remove door lock 99 gmc savana


How do you replace the thermostat on a 1997 GMC Yukon?

Drain the water from your 1997 GMC Yukon cooling system. Remove the water supply hose. Remove the thermostat housing retaining bolts. Remove the old thermostat and replace with the new thermostat.


How do do you take the fuel pump out of a 1997 GMC 1500 picuptruck . The engine is a 4.3?

how do i remove the fuel pump from the gas tank of a 1997 1500 GMC pickup truck .The trucki has a 4.3 gasengine?