answersLogoWhite

0

I just changed the plugs on my Ford Windstar findthe spark plug wires on engine and follow them down the front of engine to where the cap is. These are the front three. To find the rear three you must remove the front panel the one near the window. to do this you must take off the windshield wipers and pop off the plastic top. Then remove the metal "lid" remove seven srews unplug the windshield wiper motor and the windshield wiper fluid line. you will then be able to follow three more spark plug lines to the three back spark plugs. Hope this helps and this is what you were looking for.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How much is estimated LABOR COST to change spark-plugs and wires on 3.8L V-6 Ford Windstar van?

loacal garage charged me $149


Does 1999 E-150 ford van 4.6 eng have spark plugs?

Yes , the 4.6 liter V8 engine in a 1999 Ford E-150 has ( 8 spark plugs )


Where are spark plugs on 2002 ford E-250 cargo van?

On a 2002 Ford E-250 cargo van, the spark plugs are located on the engine's cylinder heads. For the V8 engine, you'll find them under the ignition coils, which need to be removed to access the spark plugs. If your van has a V6 engine, the spark plugs will still be found on the cylinder heads but may be positioned differently depending on the specific engine configuration. Always refer to the vehicle's service manual for detailed instructions on accessing and replacing spark plugs.


Do you have a 3.8 engine for a 2001 Windstar Ford Van?

Do you have a 3.8 engine for a 2001 Windstar Ford Van?


How do you change the spark plugs in a 1995 GMC Safari van?

To change the spark plugs in a 1997 astro van do I have to change the spark plugs from the bottom of the engine/


You change your spark plugs on your 1998 ford wind star mini van it still wont stared?

That means its not the spark plugs........Oh ya check your gas gage...


How do you change spark plugs on a e250 ford van?

To change the spark plugs on a Ford E250 van, first, ensure the engine is cool and disconnect the negative battery cable. Remove the spark plug wires by gently twisting and pulling them off the plugs, then use a spark plug socket and ratchet to unscrew the old plugs. Before installing the new spark plugs, check the gap with a gap gauge and adjust as necessary. Finally, insert the new plugs, tighten them to the manufacturer's specifications, reattach the spark plug wires, and reconnect the battery cable.


How do you change the spark plugs in the back of the engine on a 1998 Ford Windstar GL 38 liter V6?

you can either jack your van up, supporting it on jack stands & blocking the rear wheels,and using some extentions, universals & socket & socketwrench. you can get to them from the bottom. Or you could remove the wiper arms & cowl and get to the spark plugs from the top. brewski


How do you change spark plugs on ford 1998 e-350 van?

To change the spark plugs on a 1998 Ford E-350 van, start by ensuring the engine is cool and disconnect the negative battery cable. Remove the ignition coil or spark plug wires carefully to avoid damage, then use a spark plug socket and ratchet to unscrew the old spark plugs. Check the gap on the new spark plugs, install them, and tighten them to the manufacturer's specifications. Finally, reconnect the ignition coil or spark plug wires and the battery cable.


How many tons does a 2000 ford Windstar weigh?

How many tons does a ford windstar van weigh


What freon does the 1998 ford windstar van use?

A 1998 Ford Windstar would use refrigerant 134a


How do you change spark plugs on 1989 ford e350 van?

To change the spark plugs on a 1989 Ford E350 van, first ensure the engine is cool and disconnect the battery. Remove the ignition wires carefully, labeling them for reinstallation, and then use a spark plug socket and ratchet to unscrew and remove the old spark plugs. Before installing the new plugs, check and adjust the gap if necessary, then install them by hand to avoid cross-threading, and tighten them with the socket. Finally, reconnect the ignition wires in the correct order and reconnect the battery.