answersLogoWhite

0

Connect it to one of the mounting bolts or the engine block. Match the size of the connector to a nearby bolt on the block.

User Avatar

Wiki User

18y ago

What else can I help you with?

Related Questions

How do you connect the wire from the alternator to the starter?

how do you connect the wire from the alternater to the starter?


How do you wire a starter for a go kart?

To wire a starter for a go-kart, first, connect the battery's positive terminal to the starter's positive terminal using a suitable gauge wire. Then, connect the starter's negative terminal to the go-kart's frame or battery's negative terminal for grounding. Use a push-button switch or ignition switch to connect from the battery's positive terminal to the starter solenoid, allowing the starter to engage when the button is pressed. Finally, ensure all connections are secure and insulated to prevent short circuits.


How do you connect the alternator positive and negative wire to starer?

You do not connect any wire from the alternator to the starter. The positive wire from the alternator should run to the positive on the battery, and the negative wire (if equipped) should run to the engine block (or any suitable ground). Most alternators are already grounded by the bolts holding them to the engine, but some do have a negative wire.


What does the purple wire on a starter connect to?

It is the ignition wire. The purple wire goes to the small stud on starter.


What is a proper way to connect a second starter wire?

The proper way to connect a second starter wire depends with the configuration used.


How do you know which terminal on a starter is positive and which one is ground?

THE LAST ANSWER IS CORRECT OR MORE TO THE QUESTION THERE IS NO GROUND WIRE ON A STARTERFollow the wire. One will go to ground, one to hot. Most starters are marked with a + (positive) and a - (negative) on the terminals themselves,just like your battery. Usually the larger terminal where the battery cable connects to the starter is the positive terminal. .On a most starters both posts are hot(+) and the casing is grounded(-) .Usually the bigger post is a direct wire from the battery and the smaller post is a remote wire from the starter switch.Follow the positive battery cable wire (+) to the other end, that should lead you there. Because it will be connected to the starter solenoid. Please take note, a solenoid mounted on a starter has no ground wire, but a solenoid separated from the starter and mounted on the firewall does.


Changed starters to a aftermarket model on tractor only has 1 wire on selenode what to do if you have 2 wire type?

Return starter for correct one.


How do you wire a starter to a motor on the ground?

To wire a starter to a motor on the ground, first ensure the power supply is off for safety. Connect the starter's positive terminal to the positive terminal of the motor, and the negative terminal of the starter to the negative terminal of the motor. Use appropriate gauge wires to handle the current and ensure secure connections. Finally, double-check all connections before turning on the power to test the setup.


How do you install Mitsubishi Canter 4d33 Engine starter wires?

To install the starter wires on a Mitsubishi Canter 4D33 engine, first ensure the battery is disconnected to avoid any electrical shorts. Locate the starter motor, typically situated at the bottom of the engine. Connect the positive wire (usually red) to the starter's positive terminal and the negative wire (black) to the starter's ground or negative terminal. Finally, reconnect the battery and test the starter to ensure it functions correctly.


How to connect a 3-wire LED light to a 2-wire system?

To connect a 3-wire LED light to a 2-wire system, you can use a resistor to bridge the extra wire. Connect the positive wire of the LED light to the positive wire of the system, and the negative wire of the LED light to the negative wire of the system. Use a resistor to connect the extra wire of the LED light to either the positive or negative wire of the system. This will help regulate the voltage and ensure the LED light functions properly.


How do I connect the wires on a 1986 ford F150 solenoid?

To connect the wires on a 1986 Ford F150 solenoid, start by removing the negative battery cable, then connect the wire from the ignition switch to the "S" terminal on the solenoid. Next, connect the wire from the starter to the "I" terminal on the solenoid. Finally, reconnect the negative battery cable. Be sure to consult a wiring diagram specific to your vehicle for accurate connections.


1999 Chrysler Town and Country starter installation?

To install the starter, hold the starter motor spacer in position, install the starter motor-to-transaxle bell housing bolts, tighten it, and engage the solenoid wiring connector onto the terminal. Then, connect the B+ wire, tighten the retaining nut, lower the vehicle, connect the negative battery cable and verify starter motor operation. ÊÊ